Home > PLUMBING > ROUGH PLUMBING SUPPLIES > SOLVENTS & SEALERS
Choose a sub category:
PIPE CEMENTS PIPE CLEANERS & PRIMERS THREAD SEALANT COMPOUNDS
THREAD SEALANT TAPES GAS LEAK DETECTORS PLUMBERS PUTTY
PLUMBING EPOXYS
Sort By:
1
Harvey's 017072B-500 Pipe Thread Seal Tape Harvey's 017117B Pipe Thread Seal Tape Mintcraft PMB-445 Pipe Seal Tape
0.4 density, 0.003" thick. Over 50% elongation and chemically inert. Provides a strong tight seal for any threaded joint and permits easy disassembly. Tolerates -400 to + 500 degree Fahrenheit. Suitable for use on oxygen systems. Non-toxic and non-flammable. Meets Federal Specification T-27730A. 0.4 density, 0.003" thick. Over 50% elongation and chemically inert. Provides a strong tight seal for any threaded joint and permits easy disassembly. Tolerates -400 to + 500 degree Fahrenheit. Suitable for use on oxygen systems. Non-toxic and non-flammable. Meets Federal Specification T-27730A. Mintcraft Plumbers Tape, 1/2 in Width, 300 ft Length, PTFE Backing, For Fixes Leaks and Loose Pipes
Plumb Pak 04151 Pipe Thread Seal Tape Harvey's 043010 Plumbers Putty Harvey's 017209B Pipe Thread Seal Tape
Plumb Pak Thread Seal Tape, 1/2 in Width, 520 in Length, PTFE Backing, For Threaded Pipe Will not harden, crack or crumble. Plastic putty for setting closet bowls, basin cocks, fixture faucets, strainers, sink frames, etc. Not for use on marble. Will not stick to hands. 0.4 density, 0.003" thick. Over 50% elongation and chemically inert. Provides a strong tight seal for any threaded joint and permits easy disassembly. Tolerates -400 to + 500 degree Fahrenheit. Suitable for use on oxygen systems. Non-toxic and non-flammable. Meets Federal Specification T-27730A.
Harvey's 017252-144 Pipe Thread Seal Tape Oatey 31166 Plumbers Putty Harvey's 023015-48 Pipe Joint Compound
0.4 density, 0.003" thick. Over 50% elongation and chemically inert. Provides a strong tight seal for any threaded joint and permits easy disassembly. Tolerates -400 to + 500 degree Fahrenheit. Suitable for use on oxygen systems. Non-toxic and non-flammable. Meets Federal Specification T-27730A. Perfect for use on natural surface materials found in sinks, countertops, strainers and shower bases. Remains flexible, so it is easy to work with and cleans up easily. White thread lubricant and sealant. Brushable paste dries slowly, non-hardening, withstands up to 3000 PSI on gases at temps from -50d F to +500d F. Use on water, steam, natural and LP gas, oils, fuels, dilute acids. Apply to metals, PVC, CPVC, ABS, polypropylene and nylon. All-purpose sealant for HEAVY DUTY applications. Warning: Never use any pipe thread sealant paste or stick on halogens or oxygen; use PTFE Pipe Thread Tape.
Harvey 030005-144 Pipe Thread Compound Oatey 31229 Great White Oatey 31403 Gas Line Thread Tape
Pipe thread compound in stick form. Lubricates, seals and prevents rust and corrosion. Use pipe stick on pressures to 2,000 PSI, temperatures to 350 degrees Fahrenheit for metal pipe carrying water, steam, air, ammonia, gasoline, natural gas,  butane, propane, freon, petroleum oil.  DO NOT USE ON OXYGEN SYSTEMS. Lubricates and seals all threaded joints. White, non-hardening, non-separating, non-toxic paste. Withstands up to 3,000 PSI on gases from -50 to +400 degrees Fahrenheit, and 10,000 PSI on liquids from -50 to +500 degrees Fahrenheit. For use with water, steam, natural and LP gas, oil, caustics or dilute acid lines of PVC, CPVC, ABS, Cycolac, Polypropylene, iron, steel, or copper. NSF and IAPMO listed. Brush included. Manufactured especially for natural gas, propane, butane, water, oil and chemical lines. Heavier than white tape with density of 1.35 - 1.5 grams/cubic centimeter and 4 Mil thick. Complies with MIL-T-22230A (ASG), UL 31 RO, AGA 3226 and CAN/ULC-S642. Spool - dispenser box.
Harvey's 044010 Epoxy Putty Oatey 31402D Water Line Thread Seal Tape Harvey's 017165-144 Pipe Thread Seal Tape
Hardens like steel in 20 minutes. For use on plumbing, underwater, bathroom, auto, electrical and most any place in the home. Stops leaks, easy mix, makes repairs fast. Plugs, seals, mends, patches and is non-toxic. Patches holes, cracks and mends almost anything that is broken. Excellent to rebuild or fabricate parts and as an all-purpose adhesive for metals, wood, glass, masonry, ceramics and many plastics. Do not use with polyethylene or polypropylene. Can be drilled, tapped, filed, sanded and painted like metal. Note: You must press until trapped water is forced out from under putty when repairing leaking pipes. Wet putty will require longer cure time. Provides fast positive seal for water lines, sewage lines, and sprinkler systems.  Effective on metal or plastic threads. 3 Mils thick, and density of 1.35 - 1.5 grams/cubic centimeter. Complies with MIL-T-27730A and UL 31 RO. Spool- display carton. 0.4 density, 0.003" thick. Over 50% elongation and chemically inert. Provides a strong tight seal for any threaded joint and permits easy disassembly. Tolerates -400 to + 500 degree Fahrenheit. Suitable for use on oxygen systems. Non-toxic and non-flammable. Meets Federal Specification T-27730A.
Rectorseal 55910 PVC/CPVC Primer/Cleaner Harvey's 039300 Gas Leak Detectors Oatey 31012 PVC Cement
Hi etch primer specifically formulated for all PVC and CPVC pipe applications such as potable water, pressure pipe, gas, conduit, sewers and drain, waste and vent (DWV). Fast acting, hi-etch primer prepares the surfaces for superior bonding strength, purple color ensures easy visual check for complete coverage. For use on all sizes and classes in both Schedule 40 and Schedule 80. NSF approved, LEED compliant, UPC (IAPMO) listed, meets ASTM F 656 specifications. Dauber can. Detects any gas leak in just a few seconds on all types of tubing, valve, cylinders, pressurized tanks, or any system under air, gas or oxygen pressure. May be used at temperatures between -50 to +160 degrees Fahrenheit. Non-toxic, biodegradable, user friendly, non-corrosive and non-irritating to most skin. Regular-bodied clear cement recommended for use on PVC pipe and fittings up to 4" for SCH. 40 and up to 2"  for Sch. 80 potable water pressure pipe, gas, conduit, drain waste and vent pipe.  Flows freely. Sets up quickly. Apply at temperature 40 to 110 degrees F.  NSF and UPC listed. Exceeds ASTM D-2564.
Oatey 30999 ABS Cement Harvey's 017065 Pipe Thread Seal Tape Oatey 30883 PVC Cement
Medium-bodied black cement for use on all schedules and classes of ABS pipe and fittings up to 6" diameter with interference fit. Lo-VOC solvent cement meets California South Coast Air Quality Management District 1168/316A or BAAQMD Method 40 and various environmental requirements. For all non-pressure applications. Extra heavy, full density tape especially for gas lines. Recommended leakproof sealant for lines carrying natural gas, propane, butane, water, oil and chemical installations. Use on plastic, stainless steel, aluminum and all metals, ceramic, synthetic rubber, monel and carbon pipe, conduit, valves, bolts, anything with a thread. Suitable for use on oxygen systems. Permits easy disassembly. Pressure rating 10,000 PSI; .0035 mil thick, tolerates -450 to +500 degrees Fahrenheit. Meets Federal Specification T-27730A. U.L. Listed. Medium-bodied gray cement for use on all schedules and classes of PVC pipe and fittings up to 6" diameter with interference fit. Lo-V.O.C solvent cement meets California South Coast Air Quality Management District 1168/316A or BAAQMD Method 40 and various environmental requirements. Recommended for potable water, pressure pipe, conduit and DWV. Recommended application temperature 40-110 degrees.
Rectorseal 23710 T-Plus 2 Pipe Thread Sealant Harvey's 029035 Pipe Thread Compound Harvey's 018100-24 P-4
Non-setting, multi-purpose compound contains teflon, plus synthetic fibers.  May be pressurized immediately following application.  Recommended for use on threaded galvanized steel, iron, brass, copper, aluminum, stainless steel, polyethylene, fiberglass reinforced, PVC, CPVC, and ABS pipe. Conforms to TT-1732. Gray, non-drip paste for pipe joint threads on lines carrying water, steam, air or natural gas. Prevents corrosion to threads. Never hardens, joints separate easily. Contains no lead, non-toxic. Do not apply to plastic threads. Use Harvey's TFE Paste or PTFE Tape made of TEFLON on plastic threaded joints. Brushtop bottle. Regular bodied, fast set PVC solvent cement designed for use on PVC pressure pipe and fittings up to 4". NSF certified for use in potable water, sewer, and drain, waste and vent systems and should be applied at temperatures 40 degrees to 110 degrees Fahrenheit. UPC listed. Meets requirements of ASTM D-2564. Dauber can.
Plumb Pak PP854-2 Pipe Joint Compound Rectorseal 25790 Pipe Thread Sealant Harvey's 019050-24 PVC/CPVC Purple Primer
Plumb Pak Pipe Joint Compound, 2 oz, Tube Packing Soft-set, slow drying compound seals, lubricates, protects threaded pipe and fittings.  Can be pressurized immediately for piping up through 2" and 100 psi. Recommended for use on threaded galvanized steel, iron, brass, copper, aluminum, stainless steel, polyethylene, fiberglass reinforced, and PVC pipe.  Conforms to TT-S-1932. Designed to remove gloss, dirt and grease.  Softens and penetrates bonding surfaces of PVC and CPVC pipe and fittings. Recommended for use on high gloss, hard finish bell end pipe or fittings. Apply at temperature from 40 to 110 degrees F. NSF certified. Meets performance requirements of ASTM F-656. Dauber can.
Oatey 30755 PVC/CPVC Primer Harvey's 018400-24 PVC Cement Harvey's 018450-24 P-6E
A purple-tinted aggressive primer recommended for use on PVC and CPVC pipe and fittings, all Schedules and diameters. Formulated to remove surface dirt, grease and grime as well as soften the pipe surface to allow for a fast, secure and permanent solvent weld. For use in areas where the code calls for verification that a primer has been used.  Recommended for all PVC and CPVC installations.  NSF listed.  Meets ASTM F-656. Fast setting, medium bodied PVC solvent cement specifically recommended for wet conditions or when quick pressurization is needed. Recommended for pressure pipes: Schedule 40 & 80 Types I & II, up to 6". NSF certified for use in potable water, sewer, drain, waste and vent systems. Effective temperature range is 40 degrees to 110 degrees Fahrenheit. UPC listed. Meets performance requirements of ASTM D-2564. Dauber can. For electrical PVC conduit and plumbing PVC applications. Medium bodied, medium set; designed for use on all duct and conduit applications through 6" in diameter. Apply at temperatures 40 degrees to 110 degrees fahrenheit. NSF certified for use in potable water, sewer, drain, and waste and vent systems. UPC listed. Meet requirements of ASTM D-2564. Dauber can.
PC-Plumbing 025598 2-Part Hand Moldable Epoxy Putty Christy's RH.RHBV.QP.48 PVC Cement Oatey 30780 PVC/CPVC Primer/Cleaner
NSF rating, signifying it safe for contact with potable water. Works wet or dry. Quickly bonds PVC pipe and fittings for quick pressurization & maximum productivity. This premium formula bonds in wet, dry or humid weather. Medium body, very fast set & blue in color, it is the industry?s fastest acting solvent cement with the most active ingredients. For all classes and schedules of PVC pipe through 6" diameter interference fit; Schedule 80 through 4?. Red Hot Blue Glue can be used without a primer for non-pressure systems up to 6" & pressure systems below 4", if local codes permit. Ideal for PVC pipe and fitting applications; potable water, pressure, non-pressure, conduit, drain, duct, DWV, & sewer. Additionally, it is NSF & Uniform Plumbing Code listed. This product is not for use in a system using or being tested with compressed air or gases. Purple-tinted all purpose primer/cleaner for PVC and CPVC pipe and fittings. Removes surface dirt, grease and grime as well as softens pipe in preparation for solvent cement. Purple tint for verification for code. Apply at temperatures 40 degrees Fahrenheit to 100 degrees Fahrenheit.
Oatey 31230 Great White Rectorseal 55902 PVC Cement Oatey 30917 ABS Cement
Lubricates and seals all threaded joints. White, non-hardening, non-separating, non-toxic paste. Withstands up to 3,000 PSI on gases from -50 to +400 degrees Fahrenheit, and 10,000 PSI on liquids from -50 to +500 degrees Fahrenheit. For use with water, steam, natural and LP gas, oil, caustics or dilute acid lines of PVC, CPVC, ABS, Cycolac, Polypropylene, iron, steel, or copper. NSF and IAPMO listed. Brush included. Regular body cement specifically formulated for all PVC pipe applications such as potable water, pressure pipe, gas, conduit, sewers, and drain, waste and vent (DWV). For use on PVC pipe through 2" Schedule 40 pressure piping and up to and including 4" Schedule 40 non-pressure (DWV) piping; it may also be used for making up transition joints between ABS and PVC in non-pressure (DWV) piping. Dauber top. Medium-bodied ABS resin in solvent solution formula for use on ABS pipe and fittings up to 6" in diameter. Formulated especially for the hot, arid climates in the western states. Use for all non-pressure applications, for all types and grades of ABS pipe and fittings for DWV. Meets ASTM D-2235. SALES AREA - ONLY IN THE WESTERN REGION.
Oatey 30818 All-Purpose Cement Harvey 019100-24 All Purpose Pipe Cleaner Harvey's 018500-24 A-6
Medium-bodied milky clear cement for ABS, PVC, or CPVC up to 6" diameter. Recommended for pipe and fittings schedule 40 and schedule 80, potable water, pressure pipe, gas, conduit, and DWV. Recommended application temperature  40 degrees F to 110 degrees F. Meets performance requirements of ASTM D-2564, D-2235, F-493. Check local codes for acceptability of this product. All-purpose pipe cleaner designed to thoroughly clean pipe. Can be used on ABS, CPVC, and PVC pipe and fittings. Apply at temperatures from 40 degrees to 110 degrees fahrenheit. Flows freely and evaporates quickly. Dauber can. Medium bodied, medium set, ABS solvent cement designed for use on non-pressure ABS pipe and fittings: Schedule 40, Types I & II, up to 6". Apply at temperatures 40 degrees to 110 degrees fahrenheit. NSF certified and UPC listed. Meets requirements of ASTM D-2235. Dauber can.
Harvey's 018110-24 P-4 Harvey's 018200-24 P-2 PVC Cement Oatey 31128 CPVC Pipe and Fitting Cement
Regular bodied, fast set PVC solvent cement designed for use on PVC pressure pipe and fittings up to 4". NSF certified for use in potable water, sewer, and drain, waste and vent systems and should be applied at temperatures 40 degrees to 110 degrees Fahrenheit. UPC listed. Meets requirements of ASTM D-2564. Dauber can. Designed for use on PVC pressure pipe and fittings up to 12". Flows freely and provides a thick layer of cement on the pipe. Helps to fill gaps in larger diameter pipe and loose fitting joints. NSF certified for use in potable water, sewer, and drain, waste and vent systems and should be applied at temperatures 40 degrees to 110 degrees fahrenheit. UPC listed. Meets requirements of ASTM D-2564. Dauber can. Medium-bodied, fast setting formula for use on CPVC pipe and tubing with interference fits only. 40 to 110 degrees Fahrenheit optimum temperature. For use on smallest diameter through 6" diameters. Particularly suited to hot water pipe applications up to 200 degrees. Meets ASTM-F-493. NSF, UPC and IAPMO listed.
Oatey 31177 Stain-Free Plumbers Putty Harvey's 044150-12 Epoxy Putty Harvey's 018700-24 C-4
Perfect for use on natural surface materials found in sinks, countertops, strainers and shower bases. Remains flexible, so it is easy to work with and cleans up easily. Hardens like steel in 20 minutes. For use on plumbing, underwater, bathroom, auto, electrical and most any place in the home. Stops leaks, easy mix, makes repairs fast. Plugs, seals, mends, patches and is non-toxic. Patches holes, cracks and mends almost anything that is broken. Excellent to rebuild or fabricate parts and as an all-purpose adhesive for metals, wood, glass, masonry, ceramics and many plastics. Do not use with polyethylene or polypropylene. Can be drilled, tapped, filed, sanded and painted like metal. Note: You must press until trapped water is forced out from under putty when repairing leaking pipes. Wet putty will require longer cure time. Regular bodied, fast set CPVC solvent cement designed for use on CPVC pipe and fittings: Schedule 80 and Copper Tube Size, CPVC hot and cold water pipe and fittings up to 4" in diameter. Flows freely and provides a thick layer of cement on the pipe. NSF certified for use in potable water, sewer, drain, waste and vent systems. Should be applied at temperatures 40 degrees to 110 degrees fahrenheit. UPC listed. Meets ASTM F-493. Dauber can.
Harvey's 018000-24 Mp-6 Oatey 30889 ABS Cement Oatey 31013 PVC Cement
Medium bodied, medium set multi-purpose cement designed for use on PVC, CPVC, and ABS pipe and fittings: Schedule 40 & 80, Types I & II, up to 6". For potable water, pressure pipe, conduit, drain waste, and vent pipe. Flows freely and provides a thick layer of cement on the pipe and loose fitting joints. Apply at temperatures 40 degrees to 110 degrees Fahrenheit. Dauber can. Medium-bodied black cement for use on all schedules and classes of ABS pipe and fittings up to 6" diameter with interference fit. Lo-VOC solvent cement meets California South Coast Air Quality Management District 1168/316A or BAAQMD Method 40 and various environmental requirements. For all non-pressure applications. Regular-bodied clear cement recommended for use on PVC pipe and fittings up to 4" for SCH. 40 and up to 2"  for Sch. 80 potable water pressure pipe, gas, conduit, drain waste and vent pipe.  Flows freely. Sets up quickly. Apply at temperature 40 to 110 degrees F.  NSF and UPC listed. Exceeds ASTM D-2564.
Rectorseal 55912 PVC/CPVC Primer/Cleaner Harvey's 043050 Plumbers Putty Oatey 30890 Rain-R-Shine
Hi etch primer specifically formulated for all PVC and CPVC pipe applications such as potable water, pressure pipe, gas, conduit, sewers and drain, waste and vent (DWV). Fast acting, hi-etch primer prepares the surfaces for superior bonding strength, purple color ensures easy visual check for complete coverage. For use on all sizes and classes in both Schedule 40 and Schedule 80. NSF approved, LEED compliant, UPC (IAPMO) listed, meets ASTM F 656 specifications. Dauber can. Will not harden, crack or crumble. Plastic putty for setting closet bowls, basin cocks, fixture faucets, strainers, sink frames, etc. Not for use on marble. Will not stick to hands. Medium-bodied, fast-setting, colored cement recommended for PVC pipe and fittings up to 6" in diameter. Formulated for wet conditions and/or when quick pressurization and fast installation is needed. For Sch. 40 and Sch. 80 potable water pressure pipe, irrigation, gas, conduit and drain waste and vent pipe. Flows freely and covers with a thicker layer than regular PVC cement. Apply at 40 to 110 degrees Fahrenheit.
Oatey 31910 Flow-Guard Gold Brass Craft PS1087 Seal 'N Check Kit Harvey 019110-24 All Purpose Pipe Cleaner
Medium-bodied CPVC resin in solvent solution formula for copper tube size (CTS) CPVC hot and cold potable water pipe and fittings up to 2" diameter interference fit only and systems up to 180 degrees Fahrenheit. Faster cure time/reduced installation time. May be used without primer where local codes permit. Low VOC with reduced solvent emissions. Exceeds new environmental requirements, meets various California district rules and ASTM F-493. Pipe thread sealant is used to seal male to female pipe threads. The leak detection solution is applied (poured) on the joints of a gas installation to detect unsafe seals in the component-to-component connections (shut-off valve to adapter to gas connector, and gas connector to adapter to appliance regulator). Bubbles in the solution will indicate a leak. The pipe thread sealant is preferred over gas PTFE tape because of its fluidity - it seals up the crevices of the Male to Female thread engagement and provides a better seal. The leak detection solution does not contain soap or detergents, eliminating a false reading. All-purpose pipe cleaner designed to thoroughly clean pipe. Can be used on ABS, CPVC, and PVC pipe and fittings. Apply at temperatures from 40 degrees to 110 degrees fahrenheit. Flows freely and evaporates quickly. Dauber can.
Harvey 19520 All Purpose Pipe Cleaner Harvey's 019060-24 PVC/CPVC Purple Primer Oatey 31129 CPVC Pipe and Fitting Cement
Convenient project pack contains 4 oz. all-purpose pipe cleaner, and 4 oz. multi-purpose solvent cement. For most ABS, PVC, or CPVC projects. Twin pack. Designed to remove gloss, dirt and grease.  Softens and penetrates bonding surfaces of PVC and CPVC pipe and fittings. Recommended for use on high gloss, hard finish bell end pipe or fittings. Apply at temperature from 40 to 110 degrees F. NSF certified. Meets performance requirements of ASTM F-656. Dauber can. Medium-bodied, fast setting formula for use on CPVC pipe and tubing with interference fits only. 40 to 110 degrees Fahrenheit optimum temperature. For use on smallest diameter through 6" diameters. Particularly suited to hot water pipe applications up to 200 degrees. Meets ASTM-F-493. NSF, UPC and IAPMO listed.
Oatey 30779 All Purpose Pipe Cleaner Oatey 30750 Pipe Primer/Cleaner Harvey's 018510-24 A-6
For plastic pipes and fittings, all Schedules and all diameters. A fast-acting cleaner to remove surface dirt, grease and grime. Flows freely and evaporates quickly. Does not penetrate pipe surface. Recommended for use with PVC and CPVC pipe and fittings. Formulated to remove dirt and oil from the surface of the piping, as well as soften the piping in preparation for solvent welding. NSF Standard 61 listed for PW, DWV, and sewer. Meets ASTM standard F 656. Medium bodied, medium set, ABS solvent cement designed for use on non-pressure ABS pipe and fittings: Schedule 40, Types I & II, up to 6". Apply at temperatures 40 degrees to 110 degrees fahrenheit. NSF certified and UPC listed. Meets requirements of ASTM D-2235. Dauber can.
Harvey's 023030 Pipe Joint Compound Oatey 30850 PVC Cement Harvey's 025020 Pipe Thread Compound
White thread lubricant and sealant. Brushable paste dries slowly, non-hardening, withstands up to 3000 PSI on gases at temps from -50d F to +500d F. Use on water, steam, natural and LP gas, oils, fuels, dilute acids. Apply to metals, PVC, CPVC, ABS, polypropylene and nylon. All-purpose sealant for HEAVY DUTY applications. Warning: Never use any pipe thread sealant paste or stick on halogens or oxygen; use PTFE Pipe Thread Tape. Heavy-bodied clear cement for PVC pipe and fittings. Up to 12" diameter for Schedule 40 and Schedule 80. Recommended for ALL grades and types of PVC pipe and fittings, potable water, pressure pipe, gas, conduit and DWV. Helps fill gaps in larger diameter pipe and loose fitting joints. Apply at temperatures 40 degrees Fahrenheit to 110 degrees Fahrenheit. Exceeds ASTM D-2564. NSF and UPC listed. Use on all metals, plastic PVC, CPVC, ABS and nylon threads. Tolerates -50 F to +400 degrees Fahrenheit; gas to 3000 PSI, liquid to 6000 PSI. Soft, slow drying, never seizes, allows easy disassembly. SEALANT for all types of gas lines.  Brushtop bottle.
Oatey 30756 PVC/CPVC Primer Rectorseal 55970 Abs/PVC/CPVC Cement Plumb Pak PP854-1 Pipe Thread Sealant
A purple-tinted aggressive primer recommended for use on PVC and CPVC pipe and fittings, all Schedules and diameters. Formulated to remove surface dirt, grease and grime as well as soften the pipe surface to allow for a fast, secure and permanent solvent weld. For use in areas where the code calls for verification that a primer has been used.  Recommended for all PVC and CPVC installations.  NSF listed.  Meets ASTM F-656. Medium body multipurpose cement formulated for use on all PVC, CPVC and ABS pipe applications such as potable water, conduit and drain, waste and vent (DWV). It is for use on all PVC, CPVC and ABS pipe classes for pressure systems through 2" Schedule 40 and non-pressure piping systems through 6" Schedule 40 (excluding Schedule 80), also for use on transition joints to join PVC to CPVC and PVC to ABS. Exceeds ASTM F 493 specifications and is LEED compliant. Dauber top. Plumb Pak Pipe Thread Sealant, Teflon, 1 oz, Tube Packing
Oatey Fix-It Epoxy Putty Brass Craft PSC1094L Gas Leak Detectors Harvey's 018410-24 PVC Cement
For sealing, patching and mending compound. Repairs anything that leaks or is broken. Steel filled, mixes in your hands and hardens in minutes. Perfect for fabricating or rebuilding parts. May be drilled, tapped, filed, sealed and painted. Resists abrasion and a variety of chemicals. Contains no solvents, is non-toxic and will not shrink. Used for natural, LP gas, mixed, manufactured, and LP gas-air mixtures. Fast setting, medium bodied PVC solvent cement specifically recommended for wet conditions or when quick pressurization is needed. Recommended for pressure pipes: Schedule 40 & 80 Types I & II, up to 6". NSF certified for use in potable water, sewer, drain, waste and vent systems. Effective temperature range is 40 degrees to 110 degrees Fahrenheit. UPC listed. Meets performance requirements of ASTM D-2564. Dauber can.
Harvey's 018210-24 P-12 Oatey 30900 ABS/PVC Transition Cement Harvey 019120-12 All Purpose Pipe Cleaner
Designed for use on PVC pressure pipe and fittings up to 12". Flows freely and provides a thick layer of cement on the pipe. Helps to fill gaps in larger diameter pipe and loose fitting joints. NSF certified for use in potable water, sewer, and drain, waste and vent systems and should be applied at temperatures 40 degrees to 110 degrees fahrenheit. UPC listed. Meets requirements of ASTM D-2564. Dauber can. Medium-bodied, green PVC resin in solvent solution formula for use in joining all schedules of ABS to PVC pipe and fittings up to 6" diameter in non-pressure transition joints. 40 to 110 degrees Fahrenheit recommended application temperature. Meets ASTM D-3138. All-purpose pipe cleaner designed to thoroughly clean pipe. Can be used on ABS, CPVC, and PVC pipe and fittings. Apply at temperatures from 40 degrees to 110 degrees fahrenheit. Flows freely and evaporates quickly. Dauber can.
Harvey's 043105 Plumbers Putty Oatey 30821 All-Purpose Cement Rectorseal 31631 Tru-Blu
Will not harden, crack or crumble. Plastic putty for setting closet bowls, basin cocks, fixture faucets, strainers, sink frames, etc. Not for use on marble. Will not stick to hands. Medium-bodied milky clear cement for ABS, PVC, or CPVC up to 6" diameter. Recommended for pipe and fittings schedule 40 and schedule 80, potable water, pressure pipe, gas, conduit, and DWV. Recommended application temperature  40 degrees F to 110 degrees F. Meets performance requirements of ASTM D-2564, D-2235, F-493. Check local codes for acceptability of this product. Fast drying, adhesive thread sealant especially suited for high vibration environments such as refrigeration or compressor applications. Stays flexible - designed for areas of high vibration and thermal expansion/contraction. Can also be used as a positive lock and seal on threaded fasteners. Lead free and contains no metal. For use with water (hot or cold). Brushable from 20 degree F to 140 degree F. Excellent as a gasket adhesive on flanges. Low odor, non-separating. Lubricates and protects threads. Easy application - brush top applicator. Meets Federal Specification TT-S-1732.
Rectorseal 55914 PVC/CPVC Primer/Cleaner Harvey's 018710-24 C-4 CPVC Cement Oatey 31911 Flow-Guard Gold
Hi etch primer specifically formulated for all PVC and CPVC pipe applications such as potable water, pressure pipe, gas, conduit, sewers and drain, waste and vent (DWV). Fast acting, hi-etch primer prepares the surfaces for superior bonding strength, purple color ensures easy visual check for complete coverage. For use on all sizes and classes in both Schedule 40 and Schedule 80. NSF approved, LEED compliant, UPC (IAPMO) listed, meets ASTM F 656 specifications. Dauber can. Regular bodied, fast set CPVC solvent cement designed for use on CPVC pipe and fittings: Schedule 80 and Copper Tube Size, CPVC hot and cold water pipe and fittings up to 4" in diameter. Flows freely and provides a thick layer of cement on the pipe. NSF certified for use in potable water, sewer, drain, waste and vent systems. Should be applied at temperatures 40 degrees to 110 degrees fahrenheit. UPC listed. Meets ASTM F-493. Dauber can. Medium-bodied CPVC resin in solvent solution formula for copper tube size (CTS) CPVC hot and cold potable water pipe and fittings up to 2" diameter interference fit only and systems up to 180 degrees Fahrenheit. Faster cure time/reduced installation time. May be used without primer where local codes permit. Low VOC with reduced solvent emissions. Exceeds new environmental requirements, meets various California district rules and ASTM F-493.
Oatey 30891 Rain-R-Shine Harvey's 019550 Primer/Cement Pack Harvey's 018010-24 Mp-6
Medium-bodied, fast-setting, colored cement recommended for PVC pipe and fittings up to 6" in diameter. Formulated for wet conditions and/or when quick pressurization and fast installation is needed. For Sch. 40 and Sch. 80 potable water pressure pipe, irrigation, gas, conduit and drain waste and vent pipe. Flows freely and covers with a thicker layer than regular PVC cement. Apply at 40 to 110 degrees Fahrenheit. Convenient project pack contains 4 oz. purple primer, and 4 oz. blue PVC wet set cement. For most wet condition projects. Twin pack. Medium bodied, medium set multi-purpose cement designed for use on PVC, CPVC, and ABS pipe and fittings: Schedule 40 & 80, Types I & II, up to 6". For potable water, pressure pipe, conduit, drain waste, and vent pipe. Flows freely and provides a thick layer of cement on the pipe and loose fitting joints. Apply at temperatures 40 degrees to 110 degrees Fahrenheit. Dauber can.
Oatey 32161 Hot Blue Lava PVC Cement Harvey's 019530 Primer/Cement Pack Oatey 30246 Primer/Cement Pack
Medium-bodied blue cement for use on all schedules and classes of PVC pipe and fittings up to 6" diameter with interference fit. Lo-V.O.C. Solvent Cement meets California South Coast Air Quality Management District (SCAQMD) 1168/316A or BAAQMD Method 40 and various environmental requirements. Very fast-setting hot cement formulated for wet conditions and/or quick pressurization and fast installation. Recommended for potable water, sewer and DWV applications. Recommended application temperature 40 Deg F to 110 Deg F. No primer needed on non-pressure DWV, where local codes permit. Meets ASTM D2564. Convenient project pack contains 4 oz. purple primer and 4 oz. PVC solvent cement. For most PVC pipe projects. Twin pack. Contains one can of  regular clear PVC cement, and one can of NSF purple primer. Ideal size for most pipe installations.
Oatey 30782 All Purpose Pipe Cleaner PRIMER CPVC/PURPLE HANDY 4OZ  Harvey's 018520-12 A-6
For plastic pipes and fittings, all Schedules and all diameters. A fast-acting cleaner to remove surface dirt, grease and grime. Flows freely and evaporates quickly. Does not penetrate pipe surface. Contains 1 can of CPVC Cement and 1 can of NSF Purple Primer. Medium bodied, medium set, ABS solvent cement designed for use on non-pressure ABS pipe and fittings: Schedule 40, Types I & II, up to 6". Apply at temperatures 40 degrees to 110 degrees fahrenheit. NSF certified and UPC listed. Meets requirements of ASTM D-2235. Dauber can.
Oatey 15804 Hercules Pipe Thread Sealant Rectorseal 55973 Abs/PVC/CPVC Cement Harvey's 018120-12 P-4
For use on both plastic and metal pipe and fittings. Grit-free and does not contain PTFE (teflon). Sets soft; no cure time required. Never hardens, cracks or becomes brittle. No odor. Non-separating, non-flammable, and non-hazardous. Leak-proof hydraulic resistance to 12,000 psi. Withstands gas pressure to 2,600 psi. Performs over a temperature range of -50 degrees to 400 degrees F (on steel pipe). For use on all metals, including galvanized steel, black iron, aluminum, copper, brass, stainless steel, and on PVC, ABS, and CPVC plastics (for use on specific brands of CPVC pipe, verify suitability with pipe manufacturer). Not recommended for lines carrying concentrated acids, alkalis, ketones, and oxygen. Certified to ANSI/NSF Standard 61; safe for drinking water lines. UPC listed. Meets CSA requirements 4-90 for gas. Meets Fed. Spec. TT-S-1732. Medium body multipurpose cement formulated for use on all PVC, CPVC and ABS pipe applications such as potable water, conduit and drain, waste and vent (DWV). It is for use on all PVC, CPVC and ABS pipe classes for pressure systems through 2" Schedule 40 and non-pressure piping systems through 6" Schedule 40 (excluding Schedule 80), also for use on transition joints to join PVC to CPVC and PVC to ABS. Exceeds ASTM F 493 specifications and is LEED compliant. Dauber top. Regular bodied, fast set PVC solvent cement designed for use on PVC pressure pipe and fittings up to 4". NSF certified for use in potable water, sewer, and drain, waste and vent systems and should be applied at temperatures 40 degrees to 110 degrees Fahrenheit. UPC listed. Meets requirements of ASTM D-2564. Dauber can.
Oatey 30863 PVC Cement Oatey 30783 PVC/CPVC Primer/Cleaner Harvey's 029048 Pipe Thread Compound
Heavy-bodied clear cement for PVC pipe and fittings. Up to 12" diameter for Schedule 40 and Schedule 80. Recommended for ALL grades and types of PVC pipe and fittings, potable water, pressure pipe, gas, conduit and DWV. Helps fill gaps in larger diameter pipe and loose fitting joints. Apply at temperatures 40 degrees Fahrenheit to 110 degrees Fahrenheit. Exceeds ASTM D-2564. NSF and UPC listed. Purple-tinted all purpose primer/cleaner for PVC and CPVC pipe and fittings. Removes surface dirt, grease and grime as well as softens pipe in preparation for solvent cement. Purple tint for verification for code. Apply at temperatures 40 degrees Fahrenheit to 100 degrees Fahrenheit. Gray, non-drip paste for pipe joint threads on lines carrying water, steam, air or natural gas. Prevents corrosion to threads. Never hardens, joints separate easily. Contains no lead, non-toxic. Do not apply to plastic threads. Use Harvey's TFE Paste or PTFE Tape made of TEFLON on plastic threaded joints. Brushtop bottle.
Harvey's 018220-12 P-2 PVC Cement Rectorseal 23631 T-Plus 2 Christy's RH.RHBV.HP.40 PVC Cement
Designed for use on PVC pressure pipe and fittings up to 12". Flows freely and provides a thick layer of cement on the pipe. Helps to fill gaps in larger diameter pipe and loose fitting joints. NSF certified for use in potable water, sewer, and drain, waste and vent systems and should be applied at temperatures 40 degrees to 110 degrees fahrenheit. UPC listed. Meets requirements of ASTM D-2564. Dauber can. Non-setting, multi-purpose compound contains teflon, plus synthetic fibers.  May be pressurized immediately following application.  Recommended for use on threaded galvanized steel, iron, brass, copper, aluminum, stainless steel, polyethylene, fiberglass reinforced, PVC, CPVC, and ABS pipe. Conforms to TT-1732. Quickly bonds PVC pipe and fittings for quick pressurization & maximum productivity. This premium formula bonds in wet, dry or humid weather. Medium body, very fast set & blue in color, it is the industry?s fastest acting solvent cement with the most active ingredients. For all classes and schedules of PVC pipe through 6" diameter interference fit; Schedule 80 through 4?. Red Hot Blue Glue can be used without a primer for non-pressure systems up to 6" & pressure systems below 4", if local codes permit. Ideal for PVC pipe and fitting applications; potable water, pressure, non-pressure, conduit, drain, duct, DWV, & sewer. Additionally, it is NSF & Uniform Plumbing Code listed. This product is not for use in a system using or being tested with compressed air or gases.
Rectorseal 25631 Pipe Thread Sealant Oatey 31094 PVC Cement Oatey 30892 ABS Cement
Soft-set, slow drying compound seals, lubricates, protects threaded pipe and fittings.  Can be pressurized immediately for piping up through 2" and 100 psi. Recommended for use on threaded galvanized steel, iron, brass, copper, aluminum, stainless steel, polyethylene, fiberglass reinforced, and PVC pipe.  Conforms to TT-S-1932. Heavy duty gray cement for use on all schedules and classes PVC pipe and fittings up to 12" diameter with interference fit, up to 18" for non-pressure. Lo-V.O.C. solvent cement meets California South Coast Air Quality Management District 1168/316A or BAAQMD Method 40 and various environmental requirements. Thick formula fills gaps in large diameter pipe and loose fitting joints. Recommended for potable water, pressure pipe, conduit and DWV. Medium-bodied black cement for use on all schedules and classes of ABS pipe and fittings up to 6" diameter with interference fit. Lo-VOC solvent cement meets California South Coast Air Quality Management District 1168/316A or BAAQMD Method 40 and various environmental requirements. For all non-pressure applications.
Harvey's 025050 Pipe Thread Compound Harvey's 023045 Pipe Joint Compound Oatey 31014 PVC Cement
Use on all metals, plastic PVC, CPVC, ABS and nylon threads. Tolerates -50 F to +400 degrees Fahrenheit; gas to 3000 PSI, liquid to 6000 PSI. Soft, slow drying, never seizes, allows easy disassembly. SEALANT for all types of gas lines.  Brushtop bottle. White thread lubricant and sealant. Brushable paste dries slowly, non-hardening, withstands up to 3000 PSI on gases at temps from -50d F to +500d F. Use on water, steam, natural and LP gas, oils, fuels, dilute acids. Apply to metals, PVC, CPVC, ABS, polypropylene and nylon. All-purpose sealant for HEAVY DUTY applications. Warning: Never use any pipe thread sealant paste or stick on halogens or oxygen; use PTFE Pipe Thread Tape. Regular-bodied clear cement recommended for use on PVC pipe and fittings up to 4" for SCH. 40 and up to 2"  for Sch. 80 potable water pressure pipe, gas, conduit, drain waste and vent pipe.  Flows freely. Sets up quickly. Apply at temperature 40 to 110 degrees F.  NSF and UPC listed. Exceeds ASTM D-2564.
Oatey 30812 Bonding Adhesive ProPoxy 20 25515 Fast Acting Epoxy Putty Oatey 30925 ABS/PVC Transition Cement
X-15 PVC bonding adhesive is formulated for use to join two sheets of PVC shower pan liner membrane together. Provides permanent, watertight seal to form larger membrane for use in tile shower or other concealed water-proofing applications. Seals, mends, bonds, and repairs. Made of pre-measured, steel reinforced dark gray/black epoxy resin with a contrasting strip of hardener embedded in the center. Two part compound mixes to form a permanent steel-hard bond. Adheres to almost any surface. Can be drilled, filed, sanded, painted, and machined. Applies to damp or wet surfaces. Non-conductive. Medium-bodied, green PVC resin in solvent solution formula for use in joining all schedules of ABS to PVC pipe and fittings up to 6" diameter in non-pressure transition joints. 40 to 110 degrees Fahrenheit recommended application temperature. Meets ASTM D-3138.
Oatey 32166 Hot Orange Lava Harvey's 019070-12 PVC/CPVC Purple Primer Harvey's 018420-12 PVC Cement
Heavy-bodied orange cement for use on all schedules and classes of CPVC pipe and fittings up to 6? diameter with interference fit. One-step, fast curing cement designed for cut-in applications where limited time is available for down-time.  Lo-V.O.C. solvent cement meets California South Coast Air Quality Management District (SCAQMD) 1168/316A or BAAQMD Method 40 and various environmental requirements. For commercial hot and cold water systems up to 200 DegF. Recommended application temperature 40 Deg F to 110 Deg F. Approved for Flowguard Gold and Corzan CPVC piping systems. Meets ASTM F-493 and ASTM D-2846. Designed to remove gloss, dirt and grease.  Softens and penetrates bonding surfaces of PVC and CPVC pipe and fittings. Recommended for use on high gloss, hard finish bell end pipe or fittings. Apply at temperature from 40 to 110 degrees F. NSF certified. Meets performance requirements of ASTM F-656. Dauber can. Fast setting, medium bodied PVC solvent cement specifically recommended for wet conditions or when quick pressurization is needed. Recommended for pressure pipes: Schedule 40 & 80 Types I & II, up to 6". NSF certified for use in potable water, sewer, drain, waste and vent systems. Effective temperature range is 40 degrees to 110 degrees Fahrenheit. UPC listed. Meets performance requirements of ASTM D-2564. Dauber can.
Oatey 30795 All Purpose Pipe Cleaner Harvey's 018720-12 C-4 CPVC Cement Harvey's 018020-12 Mp-6
For plastic pipes and fittings, all Schedules and all diameters. A fast-acting cleaner to remove surface dirt, grease and grime. Flows freely and evaporates quickly. Does not penetrate pipe surface. Regular bodied, fast set CPVC solvent cement designed for use on CPVC pipe and fittings: Schedule 80 and Copper Tube Size, CPVC hot and cold water pipe and fittings up to 4" in diameter. Flows freely and provides a thick layer of cement on the pipe. NSF certified for use in potable water, sewer, drain, waste and vent systems. Should be applied at temperatures 40 degrees to 110 degrees fahrenheit. UPC listed. Meets ASTM F-493. Dauber can. Medium bodied, medium set multi-purpose cement designed for use on PVC, CPVC, and ABS pipe and fittings: Schedule 40 & 80, Types I & II, up to 6". For potable water, pressure pipe, conduit, drain waste, and vent pipe. Flows freely and provides a thick layer of cement on the pipe and loose fitting joints. Apply at temperatures 40 degrees to 110 degrees Fahrenheit. Dauber can.
Christy's RH.RHBV.PT.24 PVC Cement Rectorseal 23551 T-Plus 2 Pipe Thread Sealant Harvey 019130-12 All Purpose Pipe Cleaner
Quickly bonds PVC pipe and fittings for quick pressurization & maximum productivity. This premium formula bonds in wet, dry or humid weather. Medium body, very fast set & blue in color, it is the industry?s fastest acting solvent cement with the most active ingredients. For all classes and schedules of PVC pipe through 6" diameter interference fit; Schedule 80 through 4?. Red Hot Blue Glue can be used without a primer for non-pressure systems up to 6" & pressure systems below 4", if local codes permit. Ideal for PVC pipe and fitting applications; potable water, pressure, non-pressure, conduit, drain, duct, DWV, & sewer. Additionally, it is NSF & Uniform Plumbing Code listed. This product is not for use in a system using or being tested with compressed air or gases. Non-setting, multi-purpose compound contains teflon, plus synthetic fibers.  May be pressurized immediately following application.  Recommended for use on threaded galvanized steel, iron, brass, copper, aluminum, stainless steel, polyethylene, fiberglass reinforced, PVC, CPVC, and ABS pipe. Conforms to TT-1732. All-purpose pipe cleaner designed to thoroughly clean pipe. Can be used on ABS, CPVC, and PVC pipe and fittings. Apply at temperatures from 40 degrees to 110 degrees fahrenheit. Flows freely and evaporates quickly. Dauber can.
Oatey 15806 Hercules Pipe Thread Sealant Harvey's 018320-12 PVC Cement Oatey 30876 PVC Cement
For use on both plastic and metal pipe and fittings. Grit-free and does not contain PTFE (teflon). Sets soft; no cure time required. Never hardens, cracks or becomes brittle. No odor. Non-separating, non-flammable, and non-hazardous. Leak-proof hydraulic resistance to 12,000 psi. Withstands gas pressure to 2,600 psi. Performs over a temperature range of -50 degrees to 400 degrees F (on steel pipe). For use on all metals, including galvanized steel, black iron, aluminum, copper, brass, stainless steel, and on PVC, ABS, and CPVC plastics (for use on specific brands of CPVC pipe, verify suitability with pipe manufacturer). Not recommended for lines carrying concentrated acids, alkalis, ketones, and oxygen. Certified to ANSI/NSF Standard 61; safe for drinking water lines. UPC listed. Meets CSA requirements 4-90 for gas. Meets Fed. Spec. TT-S-1732. Fast setting, all-weather, medium bodied PVC solvent cement specifically recommended for cold weather and fast setting pressure applications. Recommended for pressure pipe: Schedule 40 & 80 Types I & II, up to 6". NSF certified for use in potable water, sewer, drain, waste and vent systems. Formulated for fast initial set up at temperatures down to 10 degrees fahrenheit. Effective temperature range -15 degrees to 110 degrees fahrenheit. Meets performance requirements of ASTM D-2564. Dauber can. Heavy-bodied clear cement for PVC pipe and fittings. Up to 12" diameter for Schedule 40 and Schedule 80. Recommended for ALL grades and types of PVC pipe and fittings, potable water, pressure pipe, gas, conduit and DWV. Helps fill gaps in larger diameter pipe and loose fitting joints. Apply at temperatures 40 degrees Fahrenheit to 110 degrees Fahrenheit. Exceeds ASTM D-2564. NSF and UPC listed.
Oatey 30834 All-Purpose Cement Oatey 31095 PVC Cement Oatey 30757 PVC/CPVC Primer
Medium-bodied milky clear cement for ABS, PVC, or CPVC up to 6" diameter. Recommended for pipe and fittings schedule 40 and schedule 80, potable water, pressure pipe, gas, conduit, and DWV. Recommended application temperature  40 degrees F to 110 degrees F. Meets performance requirements of ASTM D-2564, D-2235, F-493. Check local codes for acceptability of this product. Heavy duty gray cement for use on all schedules and classes PVC pipe and fittings up to 12" diameter with interference fit, up to 18" for non-pressure. Lo-V.O.C. solvent cement meets California South Coast Air Quality Management District 1168/316A or BAAQMD Method 40 and various environmental requirements. Thick formula fills gaps in large diameter pipe and loose fitting joints. Recommended for potable water, pressure pipe, conduit and DWV. A purple-tinted aggressive primer recommended for use on PVC and CPVC pipe and fittings, all Schedules and diameters. Formulated to remove surface dirt, grease and grime as well as soften the pipe surface to allow for a fast, secure and permanent solvent weld. For use in areas where the code calls for verification that a primer has been used.  Recommended for all PVC and CPVC installations.  NSF listed.  Meets ASTM F-656.
Oatey 31121 PVC Cement Plumb Pak PP855-1 Pipe Thread Seal Tape Oatey 31132 PVC Cement
Very heavy-bodied medium-setting gray colored cement for use on PVC pipe and fittings. Up to 18" diameter for Sch. 40 and Sch. 80. Formulated for quick installation of irrigation pipe and fittings. Recommended for all grades and types of PVC pipe and fittings, potable water, pressure pipe, gas, conduit and DWV. Builds up for large diameter installations. Fills gaps in large diameter pipe and loose fitting joints. Recommended application temperature 40 degrees F to 110 degrees F. Meets ASTM D-2564. For use on plumbing threads to prevent leaking. Medium-bodied clear cement for use on PVC pipe and fittings. Up to 6" diameter. Formulated for fast initial set-up at temperatures down to -15 degrees F to 100 degrees F. schedule 40 and schedule 80. Recommended for all grades and types of PVC pipe and fittings, potable water, pressure pipe, gas, conduit, and DWV. Non-pressure, DWV, up through 4" diameter: no primer needed where local codes permit. Meets ASTM D-2564.
Rectorseal 25551 Pipe Thread Sealant Oatey 30893 Rain-R-Shine Oatey 31226 Pipe Joint Compound
Soft-set, slow drying compound seals, lubricates, protects threaded pipe and fittings.  Can be pressurized immediately for piping up through 2" and 100 psi. Recommended for use on threaded galvanized steel, iron, brass, copper, aluminum, stainless steel, polyethylene, fiberglass reinforced, and PVC pipe.  Conforms to TT-S-1932. Medium-bodied, fast-setting, colored cement recommended for PVC pipe and fittings up to 6" in diameter. Formulated for wet conditions and/or when quick pressurization and fast installation is needed. For Sch. 40 and Sch. 80 potable water pressure pipe, irrigation, gas, conduit and drain waste and vent pipe. Flows freely and covers with a thicker layer than regular PVC cement. Apply at 40 to 110 degrees Fahrenheit. Fast set non-hardening paste which lubricates and seals threaded joints. Non-toxic; may be used on water, natural gas, steam and air lines. Perfect for applying gaskets to flanges. Not for use on plastic threads.
Oatey 32162 Hot Blue Lava PVC Cement Oatey 31015 PVC Cement Harvey's 018130-12 P-4
Medium-bodied blue cement for use on all schedules and classes of PVC pipe and fittings up to 6" diameter with interference fit. Lo-V.O.C. Solvent Cement meets California South Coast Air Quality Management District (SCAQMD) 1168/316A or BAAQMD Method 40 and various environmental requirements. Very fast-setting hot cement formulated for wet conditions and/or quick pressurization and fast installation. Recommended for potable water, sewer and DWV applications. Recommended application temperature 40 Deg F to 110 Deg F. No primer needed on non-pressure DWV, where local codes permit. Meets ASTM D2564. Regular-bodied clear cement recommended for use on PVC pipe and fittings up to 4" for SCH. 40 and up to 2"  for Sch. 80 potable water pressure pipe, gas, conduit, drain waste and vent pipe.  Flows freely. Sets up quickly. Apply at temperature 40 to 110 degrees F.  NSF and UPC listed. Exceeds ASTM D-2564. Regular bodied, fast set PVC solvent cement designed for use on PVC pressure pipe and fittings up to 4". NSF certified for use in potable water, sewer, and drain, waste and vent systems and should be applied at temperatures 40 degrees to 110 degrees Fahrenheit. UPC listed. Meets requirements of ASTM D-2564. Dauber can.
Harvey's 018230-12 P-12 Oatey 30902 ABS Cement Plumb Pak PP855-100 Pipe Thread Seal Tape
Designed for use on PVC pressure pipe and fittings up to 12". Flows freely and provides a thick layer of cement on the pipe. Helps to fill gaps in larger diameter pipe and loose fitting joints. NSF certified for use in potable water, sewer, and drain, waste and vent systems and should be applied at temperatures 40 degrees to 110 degrees fahrenheit. UPC listed. Meets requirements of ASTM D-2564. Dauber can. Medium-bodied black cement for use on all schedules and classes of ABS pipe and fittings up to 6" diameter with interference fit. Lo-VOC solvent cement meets California South Coast Air Quality Management District 1168/316A or BAAQMD Method 40 and various environmental requirements. For all non-pressure applications. For use on plumbing threads to prevent leaking.
Harvey's 018030-12 Mp-6 Oatey 31105 PVC Cement Oatey 31008 PVC Cement
Medium bodied, medium set multi-purpose cement designed for use on PVC, CPVC, and ABS pipe and fittings: Schedule 40 & 80, Types I & II, up to 6". For potable water, pressure pipe, conduit, drain waste, and vent pipe. Flows freely and provides a thick layer of cement on the pipe and loose fitting joints. Apply at temperatures 40 degrees to 110 degrees Fahrenheit. Dauber can. Heavy duty gray cement for use on all schedules and classes PVC pipe and fittings up to 12" diameter with interference fit, up to 18" for non-pressure. Lo-V.O.C. solvent cement meets California South Coast Air Quality Management District 1168/316A or BAAQMD Method 40 and various environmental requirements. Thick formula fills gaps in large diameter pipe and loose fitting joints. Recommended for potable water, pressure pipe, conduit and DWV. Heavy-bodied clear cement for PVC pipe and fittings. Up to 12" diameter for Schedule 40 and Schedule 80. Recommended for ALL grades and types of PVC pipe and fittings, potable water, pressure pipe, gas, conduit and DWV. Helps fill gaps in larger diameter pipe and loose fitting joints. Apply at temperatures 40 degrees Fahrenheit to 110 degrees Fahrenheit. Exceeds ASTM D-2564. NSF and UPC listed.
Oatey 30926 Abs/PVC Transition Cement CLEANER CLEAR 32 OUNCE        Rectorseal 25431 Pipe Thread Sealant
Medium-bodied, green PVC resin in solvent solution formula for use in joining all schedules of ABS to PVC pipe and fittings up to 6" diameter in non-pressure transition joints. 40 to 110 degrees Fahrenheit recommended application temperature. Meets ASTM D-3138. For plastic pipes and fittings, all Schedules and all diameters. A fast-acting cleaner to remove surface dirt, grease and grime. Flows freely and evaporates quickly. Does not penetrate pipe surface. Soft-set, slow drying compound seals, lubricates, protects threaded pipe and fittings.  Can be pressurized immediately for piping up through 2" and 100 psi. Recommended for use on threaded galvanized steel, iron, brass, copper, aluminum, stainless steel, polyethylene, fiberglass reinforced, and PVC pipe.  Conforms to TT-S-1932.
Oatey 31122 PVC Cement Harvey's 025080 Pipe Thread Compound Harvey's 018430-12 PVC Cement
Very heavy-bodied medium-setting gray colored cement for use on PVC pipe and fittings. Up to 18" diameter for Sch. 40 and Sch. 80. Formulated for quick installation of irrigation pipe and fittings. Recommended for all grades and types of PVC pipe and fittings, potable water, pressure pipe, gas, conduit and DWV. Builds up for large diameter installations. Fills gaps in large diameter pipe and loose fitting joints. Recommended application temperature 40 degrees F to 110 degrees F. Meets ASTM D-2564. Use on all metals, plastic PVC, CPVC, ABS and nylon threads. Tolerates -50 F to +400 degrees Fahrenheit; gas to 3000 PSI, liquid to 6000 PSI. Soft, slow drying, never seizes, allows easy disassembly. SEALANT for all types of gas lines.  Brushtop bottle. Fast setting, medium bodied PVC solvent cement specifically recommended for wet conditions or when quick pressurization is needed. Recommended for pressure pipes: Schedule 40 & 80 Types I & II, up to 6". NSF certified for use in potable water, sewer, drain, waste and vent systems. Effective temperature range is 40 degrees to 110 degrees Fahrenheit. UPC listed. Meets performance requirements of ASTM D-2564. Dauber can.
Harvey's 019080-12 PVC/CPVC Purple Primer Christy's RH.RHBV.QT PVC Cement Oatey 32167 Hot Orange Lava
Designed to remove gloss, dirt and grease.  Softens and penetrates bonding surfaces of PVC and CPVC pipe and fittings. Recommended for use on high gloss, hard finish bell end pipe or fittings. Apply at temperature from 40 to 110 degrees F. NSF certified. Meets performance requirements of ASTM F-656. Dauber can. Quickly bonds PVC pipe and fittings for quick pressurization & maximum productivity. This premium formula bonds in wet, dry or humid weather. Medium body, very fast set & blue in color, it is the industry?s fastest acting solvent cement with the most active ingredients. For all classes and schedules of PVC pipe through 6" diameter interference fit; Schedule 80 through 4?. Red Hot Blue Glue can be used without a primer for non-pressure systems up to 6" & pressure systems below 4", if local codes permit. Ideal for PVC pipe and fitting applications; potable water, pressure, non-pressure, conduit, drain, duct, DWV, & sewer. Additionally, it is NSF & Uniform Plumbing Code listed. This product is not for use in a system using or being tested with compressed air or gases. Heavy-bodied orange cement for use on all schedules and classes of CPVC pipe and fittings up to 6? diameter with interference fit. One-step, fast curing cement designed for cut-in applications where limited time is available for down-time.  Lo-V.O.C. solvent cement meets California South Coast Air Quality Management District (SCAQMD) 1168/316A or BAAQMD Method 40 and various environmental requirements. For commercial hot and cold water systems up to 200 DegF. Recommended application temperature 40 Deg F to 110 Deg F. Approved for Flowguard Gold and Corzan CPVC piping systems. Meets ASTM F-493 and ASTM D-2846.
Rectorseal 23431 T-Plus 2 Pipe Thread Sealant Oatey 30847 All-Purpose Cement Oatey 30894 Rain-R-Shine
Non-setting, multi-purpose compound contains teflon, plus synthetic fibers.  May be pressurized immediately following application.  Recommended for use on threaded galvanized steel, iron, brass, copper, aluminum, stainless steel, polyethylene, fiberglass reinforced, PVC, CPVC, and ABS pipe. Conforms to TT-1732. Medium-bodied milky clear cement for ABS, PVC, or CPVC up to 6" diameter. Recommended for pipe and fittings schedule 40 and schedule 80, potable water, pressure pipe, gas, conduit, and DWV. Recommended application temperature  40 degrees F to 110 degrees F. Meets performance requirements of ASTM D-2564, D-2235, F-493. Check local codes for acceptability of this product. Medium-bodied, fast-setting, colored cement recommended for PVC pipe and fittings up to 6" in diameter. Formulated for wet conditions and/or when quick pressurization and fast installation is needed. For Sch. 40 and Sch. 80 potable water pressure pipe, irrigation, gas, conduit and drain waste and vent pipe. Flows freely and covers with a thicker layer than regular PVC cement. Apply at 40 to 110 degrees Fahrenheit.
Harvey's 028005-144 Pipe Thread Compound Display PRIMER PURPLE 32 OUNCE        Oatey 15808 Hercules Pipe Thread Sealant
For sealing and lubricating threaded pipe joints. In smooth paste form. For steam, water, air, and natural gas. Does not contain lead. Wipes clean from hands. Hang tab tube. A purple-tinted aggressive primer recommended for use on PVC and CPVC pipe and fittings, all Schedules and diameters. Formulated to remove surface dirt, grease and grime as well as soften the pipe surface to allow for a fast, secure and permanent solvent weld. For use in areas where the code calls for verification that a primer has been used.  Recommended for all PVC and CPVC installations.  NSF listed.  Meets ASTM F-656. For use on both plastic and metal pipe and fittings. Grit-free and does not contain PTFE (teflon). Sets soft; no cure time required. Never hardens, cracks or becomes brittle. No odor. Non-separating, non-flammable, and non-hazardous. Leak-proof hydraulic resistance to 12,000 psi. Withstands gas pressure to 2,600 psi. Performs over a temperature range of -50 degrees to 400 degrees F (on steel pipe). For use on all metals, including galvanized steel, black iron, aluminum, copper, brass, stainless steel, and on PVC, ABS, and CPVC plastics (for use on specific brands of CPVC pipe, verify suitability with pipe manufacturer). Not recommended for lines carrying concentrated acids, alkalis, ketones, and oxygen. Certified to ANSI/NSF Standard 61; safe for drinking water lines. UPC listed. Meets CSA requirements 4-90 for gas. Meets Fed. Spec. TT-S-1732.
Toolbasix W9743L Pipe Seal Plumbers Tape Harvey's 017031-144 Pipe Thread Seal Tape Harvey's 017209-144 Pipe Thread Seal Tape
PTFE thread seal tape 1/2" x 0.004" x 260". Packed 30 pcs per display canister. Great checkout item. 0.4 density, 0.003" thick. Over 50% elongation and chemically inert. Provides a strong tight seal for any threaded joint and permits easy disassembly. Tolerates -400 to + 500 degree Fahrenheit. Suitable for use on oxygen systems. Non-toxic and non-flammable. Meets Federal Specification T-27730A. 0.4 density, 0.003" thick. Over 50% elongation and chemically inert. Provides a strong tight seal for any threaded joint and permits easy disassembly. Tolerates -400 to + 500 degree Fahrenheit. Suitable for use on oxygen systems. Non-toxic and non-flammable. Meets Federal Specification T-27730A.
   
 
1