Home > ELECTRICAL > ROUGH ELECTRICAL > ELECTRICAL FITTINGS
Choose a sub category:
NON METALLIC CABLE CONNECTORS BX / FLEX CONDUIT FITTINGS EMT METAL CONDUIT FITTINGS
RIGID CONDUIT FITTINGS LIQUID TIGHT CONDUIT FITTINGS METAL CONDUIT ACCESSORIES
PVC CONDUIT FITTINGS SERVICE ENTRANCE FITTINGS GROUNDING RODS/CLAMPS
PLASTIC FLEXIBLE FITTINGS CONDUIT STRAPS WASHERS / REDUCERS
METAL CONDUIT SUPPORT
Sort By:
1
Carlon E940D-CTN Standard Conduit Coupling Carlon E943D-CTN Terminal Adapter Halex 68307B Reducing Washer
Safe, non-conductive. Schedule 40 non-metallic socket type coupling for joining Schedule 40 non-metallic conduit. Will not rust or corrode. RoHS Compliance, UL Listed. Safe, non-conductive. For adapting schedule 40 non-metallic conduit to boxes, threaded fittings, metallic systems. Male threads on one end, socket end on the other. Will not rust or corrode. UL Listed, RoHS Compliance. Halex Reducing Washer, 1 X 3/4 in Trade, Steel, Galvanized, 1.11 in ID X 1-3/4 in OD, CSA Certified, UL Listed, 0.0315 in Thickness, For Indoor/Outdoor Applications
Halex 71205B 2-Hole Conduit Strap Carlon E940E-CTN/CAR Standard Conduit Coupling Carlon E942DR-CTN Conduit Adapter
Indoor or outdoor applications. Use to secure PVC conduit to wood, masonry or similar surface. Bulk packed. Safe, non-conductive. Schedule 40 non-metallic socket type coupling for joining Schedule 40 non-metallic conduit. Will not rust or corrode. RoHS Compliance, UL Listed. Safe, non-conductive. For adapting Schedule 40 non-metallic conduit to boxes, threaded fittings, metallic systems. Female threads one end, socket end on the other. Will not rust or corrode.
Halex 97521 Insulated Conduit Bushing Halex 61612B 2-Hole Snap-On Conduit Strap Carlon E940FR-CTN Standard Conduit Coupling
High impact thermoplastic. Flame retardant to 105 degrees C. Use with locknut to terminate threaded Rigid or IMC conduit to an outlet box. The rounded surface of the bushing prevents damage to wire insulation. Required by the NEC. UL Listed, CSA Approved. To support EMT conduit where greater load bearing is required. Indoor or outdoor applications. Safe, non-conductive. Schedule 40 non-metallic socket type coupling for joining Schedule 40 non-metallic conduit. Will not rust or corrode. RoHS Compliance, UL Listed.
Carlon E942ER-CTN Conduit Adapter Carlon E943E-CTN Terminal Adapter Halex 71210B 2-Hole Conduit Strap
Safe, non-conductive. For adapting Schedule 40 non-metallic conduit to boxes, threaded fittings, metallic systems. Female threads one end, socket end on the other. Will not rust or corrode. Safe, non-conductive. For adapting schedule 40 non-metallic conduit to boxes, threaded fittings, metallic systems. Male threads on one end, socket end on the other. Will not rust or corrode. UL Listed, RoHS Compliance. Indoor or outdoor applications. Use to secure PVC conduit to wood, masonry or similar surface. Bulk packed.
Halex 71212B 2-Hole Conduit Strap Halex 97525 Insulated Conduit Bushing Carlon E943FR-CTN Terminal Adapter
Indoor or outdoor applications. Use to secure PVC conduit to wood, masonry or similar surface. Bulk packed. High impact thermoplastic. Flame retardant to 105 degrees C. Use with locknut to terminate threaded Rigid or IMC conduit to an outlet box. The rounded surface of the bushing prevents damage to wire insulation. Required by the NEC. UL Listed, CSA Approved. Safe, non-conductive. For adapting schedule 40 non-metallic conduit to boxes, threaded fittings, metallic systems. Male threads on one end, socket end on the other. Will not rust or corrode. UL Listed, RoHS Compliance.
Carlon Snap Strap E978DC-CAR 1-Hole Single Conduit Strap Halex 96163 2-Hole Snap-On Conduit Strap Halex 97522 Insulated Conduit Bushing
Safe, non-conductive. To be used in accordance with NEC, Article 347.8 conduit spacing requirements. For use with Schedule 40/80 non-metallic solvent weld fittings. To support EMT conduit where greater load bearing is required. Indoor or outdoor applications. High impact thermoplastic. Flame retardant to 105 degrees C. Use with locknut to terminate threaded Rigid or IMC conduit to an outlet box. The rounded surface of the bushing prevents damage to wire insulation. Required by the NEC. UL Listed, CSA Approved.
Halex 07005B Intermediate Rigid Conduit Chase Nipple Halex 96821 Rigid Reducing Conduit Washer Halex 71215B 2-Hole Conduit Strap
Halex Conduit Chase Nipple, Intermediate, Rigid, 1/2 in Nominal, 1.02 in Hex, Die Cast Zinc, 0.68 in Length, CSA Certified, UL Listed, For use with a rigid coupling to terminate threaded conduit to a knockout box or enclosure, where space within the box is limited. used with a locknut to provide a short raceway between boxes or enclosures Use to reduce the size of the conduit hole knockout opening in a steel outlet box or other metal enclosure. Must use one inside the enclosure opening and one on the outside. UL Listed, CSA Approved. Indoor or outdoor applications. Use to secure PVC conduit to wood, masonry or similar surface. Bulk packed.
Carlon E996DR-CTN Conduit Box Adapter Carlon E996ER-CTN Conduit Box Adapter Carlon E940GR-CTN Standard Conduit Coupling
For PVC enclosures. cULus Listed. For PVC enclosures. cULus Listed. Safe, non-conductive. Schedule 40 non-metallic socket type coupling for joining Schedule 40 non-metallic conduit. Will not rust or corrode. RoHS Compliance, UL Listed.
Carlon E942FR-CTN Conduit Adapter Carlon Snap Strap E978EC-CAR 1-Hole Single Conduit Strap Carlon UA9ADB-CTN Standard Radius Rigid Conduit Elbow
Safe, non-conductive. For adapting Schedule 40 non-metallic conduit to boxes, threaded fittings, metallic systems. Female threads one end, socket end on the other. Will not rust or corrode. Safe, non-conductive. To be used in accordance with NEC, Article 347.8 conduit spacing requirements. For use with Schedule 40/80 non-metallic solvent weld fittings. For use with nonmetallic solvent weld fittings. Nonconductive, impact, corrosion and sunlight resistant. Schedule 40. UL 651 Listed to the NEC by the ETL, UL Listed.
Halex 90440 Screw-In Connector Halex 96111 1-Hole Conduit Strap Halex 96191 Rigid IMC Conduit Locknut
Zinc die cast. Use to connect flexible metallic conduit (Greenfield) to steel outlet box, load center or other metal enclosure. Fits 1/2" knock outs. Indoor or outdoor applications. Use to secure Rigid or I.M.C. conduit to wood, masonry or similar surfaces. Steel with zinc plating. Indoor or outdoor applications. Use to secure Rigid or IMC conduit or various threaded fittings to a steel outlet box or other metal enclosure.
Halex 96071 Knock Out Seals Halex 96072 Knock Out Seals Halex HX Flexible Screw-In Connector
Use to cover exposed knock-out holes in steel outlet boxes and other metal enclosures. Use to cover exposed knock-out holes in steel outlet boxes and other metal enclosures. Halex Screw-In Connector, Flexible, Series: HX, 3/8 in Nominal, Straight, 0.92 in Hex, Die Cast Zinc, 1.31 in Length, CSA Certified, UL Listed, 1/2 in Male NPSM Hub, For use to connect flexible metallic conduit to steel outlet box, load center or other metal enclosure, indoor use only
Halex HX Flexible Screw-In Connector Carlon A240D-CAR 1-Piece Conduit Coupling Halex 61220B 2-Hole Conduit Strap
Halex Screw-In Connector, Flexible, Series: HX, 1/2 in Nominal, Straight, 0.92 in Hex, Die Cast Zinc, 1.38 in Length, CSA Certified, UL Listed, 1/2 in Male NPSM Hub, For use to connect flexible metallic conduit to steel outlet box, load center or other metal enclosure, indoor use only Quick connect, fold and snap together. No cement, set screws or lock nuts. For 600 volt use in ceilings, floors and walls in residential, commercial and industrial buildings not more than three floors above grade. Colored in brilliant electric blue. For indoor use. Concrete tight when used with Carlon ENT. UL Listed. Indoor or outdoor use. Use to secure Rigid or IMC conduit to wood, masonry or similar surfaces where greater load bearing is required. UL Listed, CSA Approved.
Halex 97523 Insulated Conduit Bushing Carlon UA9ADR-CTN Standard Radius Conduit Elbow Carlon UA9AER-CTN Standard Radius Conduit Elbow
High impact thermoplastic. Flame retardant to 105 degrees C. Use with locknut to terminate threaded Rigid or IMC conduit to an outlet box. The rounded surface of the bushing prevents damage to wire insulation. Required by the NEC. UL Listed, CSA Approved. For use with nonmetallic solvent weld fittings. Nonconductive, impact, corrosion and sunlight resistant. For use with nonmetallic solvent weld fittings. Nonconductive, impact, corrosion and sunlight resistant.
Carlon E940HR-CTN Standard Conduit Coupling Carlon E943GR-CTN Terminal Adapter Halex 96192 Rigid IMC Conduit Locknut
Safe, non-conductive. Schedule 40 non-metallic socket type coupling for joining Schedule 40 non-metallic conduit. Will not rust or corrode. RoHS Compliance, UL Listed. Safe, non-conductive. For adapting schedule 40 non-metallic conduit to boxes, threaded fittings, metallic systems. Male threads on one end, socket end on the other. Will not rust or corrode. UL Listed, RoHS Compliance. Steel with zinc plating. Indoor or outdoor applications. Use to secure Rigid or IMC conduit or various threaded fittings to a steel outlet box or other metal enclosure.
Halex 96831 Rigid Reducing Conduit Washer Halex 96832 Rigid Reducing Conduit Washer Carlon UA7ADB-CTN Standard Radius Conduit Elbow
Use to reduce the size of the conduit hole knockout opening in a steel outlet box or other metal enclosure. Must use one inside the enclosure opening and one on the outside. UL Listed, CSA Approved. Use to reduce the size of the conduit hole knockout opening in a steel outlet box or other metal enclosure. Must use one inside the enclosure opening and one on the outside. UL Listed, CSA Approved. For use with nonmetallic solvent weld fittings. Nonconductive, impact, corrosion and sunlight resistant. UL Listed E35297.
Carlon UA9AEB-CTN Standard Radius Rigid Conduit Elbow Halex 71220B 2-Hole Conduit Strap Halex 96560 Beam Clamp
For use with nonmetallic solvent weld fittings. Nonconductive, impact, corrosion and sunlight resistant. Schedule 40. UL 651 Listed to the NEC by the ETL, UL Listed. Indoor or outdoor applications. Use to secure PVC conduit to wood, masonry or similar surface. Bulk packed. Use to secure conduit to a metal beam. Clamps on beam, girder or similar structure to provide a mounting base for attachment of a conduit hanger, either directly or by means of a threaded rod. Eliminates need to drill hole through beam.
Halex 97524 Insulated Conduit Bushing Carlon UA7ADR-CAR Standard Radius Conduit Elbow Carlon E942GR-CTN Conduit Adapter
High impact thermoplastic. Flame retardant to 105 degrees C. Use with locknut to terminate threaded Rigid or IMC conduit to an outlet box. The rounded surface of the bushing prevents damage to wire insulation. Required by the NEC. UL Listed, CSA Approved. For use with nonmetallic solvent weld fittings. Nonconductive, impact, corrosion and sunlight resistant. UL Listed E35297. Safe, non-conductive. For adapting Schedule 40 non-metallic conduit to boxes, threaded fittings, metallic systems. Female threads one end, socket end on the other. Will not rust or corrode.
Carlon E943HR-CTN Terminal Adapter Thomas & Betts E950ED-CTN Reducing Bushing Carlon A243D-CAR 1-Piece Snap-In Conduit Adapter
Safe, non-conductive. For adapting schedule 40 non-metallic conduit to boxes, threaded fittings, metallic systems. Male threads on one end, socket end on the other. Will not rust or corrode. UL Listed, RoHS Compliance. For connecting different sizes of conduit. Socket both ends, for reducing male Schedule 40/80 conduit runs or fittings to female. Non-conductive. Will not rust or corrode. Innovative one piece quick connect design for fast and easy installation. Suitable for damp locations. No glue or cement needed. Carlon Standard Blue. Concrete tight when used with appropriate ENT.
Halex 96193 Rigid Conduit Locknut Halex 96151 1-Hole Snap-On Conduit Strap Halex 90441 Screw-In Connector
Steel with zinc plating. Indoor or outdoor applications. Use to secure Rigid or IMC conduit or various threaded fittings to a steel outlet box or other metal enclosure. Indoor or outdoor applications. To support EMT conduit. Zinc die cast. Use to connect flexible metallic conduit (Greenfield) to steel outlet box, load center or other metal enclosure. Fits 1/2" knock outs.
Halex 90451 Screw-In Coupling Halex 90510 Twin Screw Clamp Connector Halex 90701 Conduit Chase Nipple
Zinc die cast. Use to join two pieces of flexible metallic conduit (Greenfield) together. Fits 1/2" knockout, non-metallic cable numbers 14/2, 12/2, 12/3 AWG or 2 number 14/2 AWG or flex cord .300 to .560 inches diameter. In a dry location, use to connect nonmetallic sheathed cable to a steel outlet box or other metal enclosure. UL, Listed, meets CSA requirements. Zinc die cast. Indoor or outdoor applications. Use to terminate threaded conduit to a knockout box or enclosure, where space within the box is limited. Used with a locknut to provide a short raceway between boxes or enclosures. UL and CSA approved.
Halex 96121 2-Hole Conduit Strap Halex 26190 Conduit Locknut Halex 07007B Intermediate Rigid Conduit Chase Nipple
Indoor or outdoor use. Use to secure Rigid or IMC conduit to wood, masonry or similar surfaces where greater load bearing is required. UL Listed, CSA Approved. Halex Conduit Locknut, 1/2 in Nominal, Steel, Zinc Plated, CSA Certified, UL Listed, For use to secure rigid, imc conduit or various threaded fittings to a steel outlet box or other metal enclosure, indoor/outdoor Halex Conduit Chase Nipple, Intermediate, Rigid, 3/4 in Nominal, 1.29 in Hex, Die Cast Zinc, 3/4 in Length, CSA Certified, UL Listed, For use with a rigid coupling to terminate threaded conduit to a knockout box or enclosure, where space within the box is limited. used with a locknut to provide a short raceway between boxes or enclosures
Halex 68612B Reducing Washer Halex 96194 Rigid IMC Conduit Locknut Halex 91530 Combination Coupling
Halex Reducing Washer, 2 X 1-1/4 in Trade, Steel, Galvanized, 1.73 in ID X 3 in OD, CSA Certified, UL Listed, 0.0315 in Thickness, For Indoor/Outdoor Applications Steel with zinc plating. Indoor or outdoor applications. Use to secure Rigid or IMC conduit or various threaded fittings to a steel outlet box or other metal enclosure. Zinc die cast. Use to join EMT conduit to non-metallic sheathed cable. #14/2, #12/3 or 2 #14/2. Indoor use only. With UPC. UL Approved.
Carlon A253D-CAR 1-Piece Snap-In Terminal Adapter Carlon A253E-CAR 1-Piece Snap-In Terminal Adapter Carlon UA7AER-CAR Standard Radius Conduit Elbow
Fold and snap together. No cement, set screws or lock nuts. For 600 volt use in ceilings, floors and walls in residential, commercial and industrial buildings not more than three floors above grade. Colored in brilliant electric blue. For indoor use. Concrete tight when used with Carlon ENT. UL Listed. Fold and snap together. No cement, set screws or lock nuts. For 600 volt use in ceilings, floors and walls in residential, commercial and industrial buildings not more than three floors above grade. Colored in brilliant electric blue. For indoor use. Concrete tight when used with Carlon ENT. UL Listed. For use with nonmetallic solvent weld fittings. Nonconductive, impact, corrosion and sunlight resistant. UL Listed E35297.
Carlon E940JR-CTN Standard Conduit Coupling Carlon E942HR Conduit Adapter Thomas & Betts E977DC-CTN 2-Hole Conduit Clamp
Safe, non-conductive. Schedule 40 non-metallic socket type coupling for joining Schedule 40 non-metallic conduit. Will not rust or corrode. RoHS Compliance, UL Listed. Safe, non-conductive. For adapting Schedule 40 non-metallic conduit to boxes, threaded fittings, metallic systems. Female threads one end, socket end on the other. Will not rust or corrode. Offers same chemical resistance as Carlon nonmetallic conduit for a complete, corrosion resistant system. UV resistant for use in direct sunlight. Use in accordance with conduit spacing requirements per NEC. Each clamp requires 2 screws, 2 nuts, and 2 washers. Gray clamps for standard conduit.
Halex 96780 Conduit Hanger Halex 96161 2-Hole Snap-On Conduit Strap Halex 96213 1-Hole Cable Strap
Use to secure and suspend conduit from overhead supports. Comes with a nut and bolt. To support EMT conduit where greater load bearing is required. Indoor or outdoor applications. Steel, use to secure BX cable to wood, masonry or similar surface.
Halex 90580 Cable Connector Halex 96112 1-Hole Conduit Strap Halex 96122 2-Hole Conduit Strap
Zinc die cast. In a dry location, use to connect BX cable to a steel outlet box or other metal enclosure. 3/8" size fits 1/2" knock outs. UL Approved. Indoor or outdoor applications. Use to secure Rigid or I.M.C. conduit to wood, masonry or similar surfaces. Indoor or outdoor use. Use to secure Rigid or IMC conduit to wood, masonry or similar surfaces where greater load bearing is required. UL Listed, CSA Approved.
Halex 91321 Reducing Conduit Bushing Halex 96781 Conduit Hanger Carlon UA7AEB-CTN Standard Radius Conduit Elbow
Zinc die cast. Indoor or outdoor applications. Use to reduce the entry size of a run of threaded conduit. UL Approved. Use to secure and suspend conduit from overhead supports. Comes with a nut and bolt. For use with nonmetallic solvent weld fittings. Nonconductive, impact, corrosion and sunlight resistant. UL Listed E35297.
Halex 64305 Intermediate Rigid Conduit Nipple Halex 64311 Intermediate Rigid Conduit Nipple Halex 13205B Reducing Bushing
Halex Conduit Nipple, Intermediate, Rigid, 1/2 in Nominal, Steel, Close Length, CSA Certified, UL Listed, For use to connect two steel outlet boxes or other metal enclosures; use to extend a length of threaded rigid or IMC conduit, indoor/outdoor Halex Conduit Nipple, Intermediate, Rigid, 1/2 in Nominal, Steel, 1-1/2 in Length, CSA Certified, UL Listed, For use to connect two steel outlet boxes or other metal enclosures; use to extend a length of threaded rigid or IMC conduit, indoor/outdoor Halex Reducing Bushing, 3/4 X 1/2 in Conduit, Rigid Conduit, Threaded End, Die Cast Steel, UL Listed, CSA Certified, For Dry Locations Applications
Halex 96843 Rigid Reducing Conduit Washer WASHER RDUCNG RGD 1-1/4X1/2IN WASHER RDUCNG RGD 1-1/4X3/4IN
Use to reduce the size of the conduit hole knockout opening in a steel outlet box or other metal enclosure. Must use one inside the enclosure opening and one on the outside. UL Listed, CSA Approved. Use to reduce the size of the conduit hole knockout opening in a steel outlet box or other metal enclosure. Must use one inside the enclosure opening and one on the outside. UL Listed, CSA Approved. Use to reduce the size of the conduit hole knockout opening in a steel outlet box or other metal enclosure. Must use one inside the enclosure opening and one on the outside. UL Listed, CSA Approved.
Carlon A240E-CAR 1-Piece Conduit Coupling Halex 91641 Box Spacer Carlon UA9AFR-CTN Standard Radius Conduit Elbow
Quick connect, fold and snap together. No cement, set screws or lock nuts. For 600 volt use in ceilings, floors and walls in residential, commercial and industrial buildings not more than three floors above grade. Colored in brilliant electric blue. For indoor use. Concrete tight when used with Carlon ENT. UL Listed. Die cast of high strength corrosion resistant zinc alloy. Locknut is reversible. It is designed to cut through protective coatings on boxes and enclosures to assure ground continuity. Use as a raceway between two steel outlet boxes or other metal enclosures. UL and CSA Listed. For use with nonmetallic solvent weld fittings. Nonconductive, impact, corrosion and sunlight resistant.
Carlon E943JRR Terminal Adapter Thomas & Betts E977EC-CTN 2-Hole Conduit Clamp Halex 90570 Combination Clamp Connector
Safe, non-conductive. For adapting schedule 40 non-metallic conduit to boxes, threaded fittings, metallic systems. Male threads on one end, socket end on the other. Will not rust or corrode. UL Listed, RoHS Compliance. Offers same chemical resistance as Carlon nonmetallic conduit for a complete, corrosion resistant system. UV resistant for use in direct sunlight. Use in accordance with conduit spacing requirements per NEC. Each clamp requires 2 screws, 2 nuts, and 2 washers. Gray clamps for standard conduit. Zinc die cast. In a dry location, use to connect flexible metallic conduit (Greenfield, BX, NM or Metal Clad) to a steel outlet box or other metal enclosure. 3/8" size fits 1/2" knock outs. UL Approved.
Halex HX Flexible Screw-In Coupling Halex SSC Flexible Set Screw Connector Halex 26197 Conduit Locknut
Halex Screw-In Coupling, Flexible, Series: HX, 1/2 in Nominal, 0.92 in Hex, Die Cast Zinc, 1.81 in Length, CSA Certified, UL Listed, For use to join two pieces of flexible metallic conduit, indoor only Halex Set Screw Connector, Flexible, Series: SSC, 1/2 in Nominal, Straight, Die Cast Zinc, 0.94 in Length X 1.46 in Width, CSA Certified, UL Listed, 0.74 - 0.94 in Cable Opening, 1/2 in Male NPSM Hub, For use to connect steel or aluminum flexible metallic conduit to a steel outlet box or other metal enclosure in dry location, indoor use only Halex Conduit Locknut, 3/4 in Nominal, Steel, Zinc Plated, CSA Certified, UL Listed, For use to secure rigid, imc conduit or various threaded fittings to a steel outlet box or other metal enclosure, indoor/outdoor
Halex 27528 Insulating Bushing Halex 96142 Flat Style Drive Strap Carlon A243E-CAR 1-Piece Snap-In Conduit Adapter
Halex Insulating Bushing, 1 in Conduit, Rigid, IMC Conduit, Threaded End, Thermoplastic, UL Listed, CSA Certified, For Indoor/Outdoor Applications Halex Drive Strap, Flat Style, 3/4 in Nominal, Steel/Nylon, Zinc Plated, 2.12 in Length x 1.2 in Width, CSA Certified, UL Listed, For Indoor/Outdoor Applications Innovative one piece quick connect design for fast and easy installation. Suitable for damp locations. No glue or cement needed. Carlon Standard Blue. Concrete tight when used with appropriate ENT.
Halex 96195 Rigid Conduit Locknut Carlon UA9AFB-CTN Standard Radius Conduit Elbow Carlon E942JR Conduit Adapter
Steel with zinc plating. Indoor or outdoor applications. Use to secure Rigid or IMC conduit or various threaded fittings to a steel outlet box or other metal enclosure. For use with nonmetallic solvent weld fittings. Nonconductive, impact, corrosion and sunlight resistant. Schedule 40. UL 651 Listed to the NEC by the ETL, UL Listed. Safe, non-conductive. For adapting Schedule 40 non-metallic conduit to boxes, threaded fittings, metallic systems. Female threads one end, socket end on the other. Will not rust or corrode.
Carlon UA7AFR-CAR Standard Radius Conduit Elbow Halex 96152 1-Hole Snap-On Conduit Strap Halex 26155 1-Hole Snap-On Conduit Strap
For use with nonmetallic solvent weld fittings. Nonconductive, impact, corrosion and sunlight resistant. UL Listed E35297. Indoor or outdoor applications. To support EMT conduit. Indoor or outdoor applications. To support EMT conduit.
Halex 96162 2-Hole Snap-On Conduit Strap Halex 90442 Screw-In Connector Halex 91100 Conduit Elbow
To support EMT conduit where greater load bearing is required. Indoor or outdoor applications. Zinc die cast. Use to connect flexible metallic conduit (Greenfield) to steel outlet box, load center or other metal enclosure. Fits 1/2" knock outs. Zinc die cast. In a dry location, use to connect flexible metallic conduit (Greenfield or BX) to a steel outlet box or other metal enclosure.
Halex 90420 Squeeze Connector Halex 90512 Twin Screw Clamp Connector Halex 96510 2-Piece Butterfly Clamp Connector
Zinc die cast. In a dry location, use to connect flexible metallic conduit (Greenfield or BX) to steel outlet box, load center or other metal enclosure. Fits 1/2" knock outs. UL Approved. Fits non metallic cable, such as Romex, number 14/2 round, number 12/3-8/3 AWG or flex cord .460 to .720 inches diameter. In a dry location, use to connect nonmetallic sheathed cable to a steel outlet box or other metal enclosure. UL Listed, meets CSA requirements. Zinc die cast. In a dry location, use to secure #14 - #10 non-metallic sheathed cable to steel outlet box or other metal enclosure. No locknut required.
Halex 91331 Reducing Conduit Bushing Halex 91332 Reducing Conduit Bushing STRAP CBL 1HOLE SRVC ENT
Zinc die cast. Indoor or outdoor applications. Use to reduce the entry size of a run of threaded conduit. UL Approved. Zinc die cast. Indoor or outdoor applications. Use to reduce the entry size of a run of threaded conduit. UL Approved. Steel, use to secure service entrance cable (SEU, SER) to wood, masonry or similar surface.
WASHER RDUCNG RGD 1-1/2X1/2IN WASHER RDUCING RGD 1-1/2X3/4IN Halex 16405B Box Spacer
Use to reduce the size of the conduit hole knockout opening in a steel outlet box or other metal enclosure. Must use one inside the enclosure opening and one on the outside. UL Listed, CSA Approved. Use to reduce the size of the conduit hole knockout opening in a steel outlet box or other metal enclosure. Must use one inside the enclosure opening and one on the outside. UL Listed, CSA Approved. Zinc die cast. Use as a raceway between two steel outlet boxes or other metal enclosures. UL Listed. Bulk packed.
Halex 26071 Knock Out Seals Halex 61225 2-Hole Conduit Strap Thomas & Betts E994DR-CTN Conduit Offset
Use to cover exposed knock-out holes in steel outlet boxes and other metal enclosures. To support EMT conduit where greater load bearing is required. Indoor or outdoor applications. Non-conductive. Will not rust or corrode.
Halex 26165 2-Hole Snap-On Conduit Strap Carlon UA7AFB-CTN Standard Radius Conduit Elbow Halex 90421 Squeeze Connector
To support EMT conduit where greater load bearing is required. Indoor or outdoor applications. For use with nonmetallic solvent weld fittings. Nonconductive, impact, corrosion and sunlight resistant. UL Listed E35297. Zinc die cast. In a dry location, use to connect flexible metallic conduit (Greenfield or BX) to steel outlet box, load center or other metal enclosure. Fits 1/2" knock outs. UL Approved.
Halex 26211 1-Hole Conduit Strap Halex HX Flexible Screw-In Connector Halex 64325 Intermediate Rigid Conduit Nipple
Steel, use to secure BX cable to wood, masonry or similar surface. Halex Screw-In Connector, Flexible, Series: HX, 3/4 in Nominal, Straight, 1.12 in Hex, Die Cast Zinc, 1.62 in Length, CSA Certified, UL Listed, 3/4 in Male NPSM Hub, For use to connect flexible metallic conduit to steel outlet box, load center or other metal enclosure, indoor use only Halex Conduit Nipple, Intermediate, Rigid, 1/2 in Nominal, Steel, 2 in Length, CSA Certified, UL Listed, For use to connect two steel outlet boxes or other metal enclosures; use to extend a length of threaded rigid or IMC conduit, indoor/outdoor
Halex 64307 Conduit Nipple Thomas And Betts Z703 1/2-25 Superstrut Halex 16010B Ground Clamp
Halex Conduit Nipple, 3/4 in Nominal, Steel, Galvanized, Close Length, CSA Certified, UL Listed, For use to connect two steel outlet boxes or other metal enclosures; use to extend a length of threaded rigid or IMC conduit, indoor/outdoor Pipe straps hold conduit and pipes in channel. They are inserted along the slot side of the channel and twisted into place. Pre-assembled with locking slot / hex head bolt. Gold-galvanized corrosion free finish. Indoor or outdoor applications. Use to secure the grounding wire to a 1/2" through 1" pipe. UL Listed. Wire size fits #10 - #2 AWG.
Halex 97526 Insulated Conduit Bushing Carlon UA9AGR-CTN Standard Radius Conduit Elbow Carlon E950FD-CAR Reducing Conduit Bushing
High impact thermoplastic. Flame retardant to 105 degrees C. Use with locknut to terminate threaded Rigid or IMC conduit to an outlet box. The rounded surface of the bushing prevents damage to wire insulation. Required by the NEC. UL Listed, CSA Approved. For use with nonmetallic solvent weld fittings. Nonconductive, impact, corrosion and sunlight resistant. For connecting different sizes of conduit. Socket both ends, for reducing male Schedule 40/80 conduit runs or fittings to female. Non-conductive. Will not rust or corrode.
Carlon UA7AGR-CAR Standard Radius Conduit Elbow Halex 26125 2-Hole Conduit Strap Halex 75403 Anti-Short Conduit Bushing
For use with nonmetallic solvent weld fittings. Nonconductive, impact, corrosion and sunlight resistant. UL Listed E35297. Indoor or outdoor use. Use to secure Rigid or IMC conduit to wood, masonry or similar surfaces where greater load bearing is required. UL Listed, CSA Approved. High dielectric plastic. Use to protect wire within flexible metallic conduit (Greenfield, BX). Insert one bushing at each end of conduit. UL Approved. No. 75400 - Fits cable range: 14/2, 14/3, 12/2 No. 75401 - Fits cable range: 14/4, 12/3, 6/1, 4/1. No. 75402 - Fits cable range: 12/4, 10/2, 10/3, 2/1. No. 75403 - Fits cable range: 10/4, 8/2, 8/3, 1/1. No. 75404 - Fits cable range: 8/4, 6/2, 6/3, 4/2, 4/3, 6/4.
Carlon E940K-CTN Conduit Coupling Halex 27511 Hit Lock Cable Connectors Halex 26153 1-Hole Snap-On Conduit Strap
Safe, non-conductive. Schedule 40 non-metallic socket type coupling for joining Schedule 40 non-metallic conduit. Will not rust or corrode. RoHS Compliance, UL Listed. Fits NM Cable: #14/2, #14/3, #12/2, #10/2, #10/3. Snap-In, no screws or locknuts required. In a dry location, use to connect non-metallic sheathed cable to a steel outlet box or other metal enclosure. Design allows for two-step installation. Push into box and insert cable. UL Approved, CSA certified. Indoor or outdoor applications. To support EMT conduit.
Halex 90702 Conduit Chase Nipple Halex 27527 Insulating Bushing Halex 26072 Knock-Out Seal
Zinc die cast. Indoor or outdoor applications. Use to terminate threaded conduit to a knockout box or enclosure, where space within the box is limited. Used with a locknut to provide a short raceway between boxes or enclosures. UL and CSA approved. Halex Insulating Bushing, 3/4 in Conduit, Rigid, IMC Conduit, Threaded End, Thermoplastic, UL Listed, CSA Certified, For Indoor/Outdoor Applications Halex Knock-Out Seal, 3/4 in Nominal, Steel, Zinc Electro Plated, 1-1/4 in Length X 0.313 in Width, CSA Certified, UL Listed, For use to cover exposed knockout holes in steel outlet boxes and other metal enclosures, indoor use only
Halex 64005 Conduit Coupling Halex 07010B Intermediate Rigid Conduit Chase Nipple Halex 26210 1-Hole Service Entrance Strap
Steel, indoor or out. Use to join threaded Rigid or IMC conduit together. UL Listed. Halex Conduit Chase Nipple, Intermediate, Rigid, 1 in Nominal, 1.53 in Hex, Die Cast Zinc, 0.87 in Length, CSA Certified, UL Listed, For use with a rigid coupling to terminate threaded conduit to a knockout box or enclosure, where space within the box is limited. used with a locknut to provide a short raceway between boxes or enclosures Steel, use to secure service entrance cable (SEU, SER) to wood, masonry or similar surface.
Halex 61240B IMC Rigid Snap-On Two-Hole Strap Thomas & Betts 700 Pipe Clamp Thomas & Betts 700 Pipe Clamp
Halex Two-Hole Strap, IMC, Rigid, Snap-On, 4 in Nominal, Steel, Zinc Electro Plated, 8 in Length X 1 in Width, CSA Certified, UL Listed, For Indoor/Outdoor Applications Thomas & Betts Pipe Clamp, Universal, Series: 700, 1/2 in Opening, 400 lb Load Capacity, Steel, ASTM A569, Electro Galvanized, Silver, 1-1/4 in Height, 16 ga Thickness, Includes: Bolt and Square Nut, OSHA Approved, 0.706 - 0.84 in Cable, For Suspend Electrical Pipes and Tubing From the Ceiling Thomas & Betts Pipe Clamp, Universal, Series: 700, 3/4 in Opening, 550 lb Load Capacity, Steel, ASTM A569, Electro Galvanized, Silver, 1-1/4 in Height, 14 ga Thickness, Includes: Bolt and Square Nut, OSHA Approved, 0.932 - 1.05 in Cable, For Suspend Electrical Pipes and Tubing From the Ceiling
CONNECTOR DPLX FLX N-MTL 3/8IN Halex 90513 Twin Screw Clamp Connector Halex 20511 Twin Screw Clamp Connector
In a dry location, use to connect two pieces of flexible armored cable (Greenfield or BX) to a steel outlet box or other metal enclosure, when using only one knock-out opening. UL Approved. Fits non metallic cable number 14/2 to number 6/3 AWG or number 3/10/3 AWG or flex cord .450 to .730 inches diameter. With a 1/2" knockout. In a dry location, use to connect nonmetallic sheathed cable to a steel outlet box or other metal enclosure. UL Listed, meets CSA requirements. Fits 1/2" knockout, non-metallic cable numbers 14/2, 12/2, 12/3 AWG or 2 number 14/2 AWG or flex cord .300 to .560 inches diameter. In a dry location, use to connect nonmetallic sheathed cable to a steel outlet box or other metal enclosure. UL, Listed, meets CSA requirements.
Halex 91531 Combination Coupling Halex 90422 Squeeze Connector Halex HX Flexible Screw-In Connector
Zinc die cast. Use to join EMT conduit to flexible metal conduit. Indoor use only. With UPC. UL Approved. Zinc die cast. In a dry location, use to connect flexible metallic conduit (Greenfield or BX) to steel outlet box, load center or other metal enclosure. Fits 1/2" knock outs. UL Approved. Halex Screw-In Connector, Flexible, Series: HX, 1 in Nominal, Straight, 1.37 in Hex, Die Cast Zinc, 1.94 in Length, CSA Certified, UL Listed, 1 in Male NPSM Hub, For use to connect flexible metallic conduit to steel outlet box, load center or other metal enclosure, indoor use only
Halex SSC Flexible Set Screw Connector Thomas & Betts E940E5-UPC Conduit Coupling Halex 26212 1-Hole Corrosion Resistant Midget Strap
Halex Set Screw Connector, Flexible, Series: SSC, 3/4 in Nominal, Straight, Die Cast Zinc, 1.15 in Length X 1.56 in Width, CSA Certified, UL Listed, 0.74 - 0.94 in Cable Opening, 3/4 in Male NPSM Hub, For use to connect steel or aluminum flexible metallic conduit to a steel outlet box or other metal enclosure in dry location, indoor use only Thomas & Betts Conduit Coupling, 3/4 in Conduit, Rigid Conduit, Socket End, SCH 40, PVC, 0.84 in ID X 1-5/16 in OD Diameter, 1-5/8 in Length, cULus E 32447, RoHS Compliant Halex Midget Strap, 1-Hole, Corrosion Resistant, 3/16 in Opening, Galvanized Steel, Electro Plated Zinc, 0.73 in Width, For Indoor/Outdoor Applications
Superstrut 200 Series Angle Bracket Fitting Thomas And Betts Z703 3/4-25 Superstrut Halex 16407B Box Spacer
For use in metal framing applications. Manufactured from hot rolled carbon steel. Pipe straps hold conduit and pipes in channel. They are inserted along the slot side of the channel and twisted into place. Pre-assembled with locking slot / hex head bolt. Gold-galvanized corrosion free finish. Zinc die cast. Use as a raceway between two steel outlet boxes or other metal enclosures. UL Listed. Bulk packed.
Halex 90514 Twin Screw Clamp Connector Halex 64007 Conduit Coupling Gardner Bender GGS-1512R Ground Screw
Fits non metallic cable number 6/3 to number 2/3 AWG flex cord .800 to 1.350 inches diameter or SE cable 3 conductor or 3 number 1/0 minimum; 3 conductor or 3 number 2/0 maximum. With 1/2" knockout. In a dry location, use to connect nonmetallic sheathed cable to a steel outlet box or other metal enclosure. UL Listed, meets CSA requirements. Steel, indoor or out. Use to join threaded Rigid or IMC conduit together. UL Listed. Green round washer head screw for switch and outlet boxes.
Thomas & Betts E950FE-CTN Reducing Bushing Thomas & Betts E994ER-CTN Conduit Offset Carlon UA7AGB-CAR Standard Radius Conduit Elbow
For connecting different sizes of conduit. Socket both ends, for reducing male Schedule 40/80 conduit runs or fittings to female. Non-conductive. Will not rust or corrode. Non-conductive. Will not rust or corrode. For use with nonmetallic solvent weld fittings. Nonconductive, impact, corrosion and sunlight resistant. UL Listed E35297.
Halex 26126 2-Hole Conduit Strap Halex 26163 2-Hole Snap-On Conduit Strap Carlon E943K-CTN Terminal Adapter
Indoor or outdoor use. Use to secure Rigid or IMC conduit to wood, masonry or similar surfaces where greater load bearing is required. UL Listed, CSA Approved. To support EMT conduit where greater load bearing is required. Indoor or outdoor applications. Safe, non-conductive. For adapting schedule 40 non-metallic conduit to boxes, threaded fittings, metallic systems. Male threads on one end, socket end on the other. Will not rust or corrode. UL Listed, RoHS Compliance.
Carlon LN43DA-CTN Liquidtight Straight Angle Conduit Connector Halex 91101 Conduit Elbow Halex 96401 Conduit Coupling
For flexible conduit. Non-metallic/non-conductive, corrosion resistant plastic. Zinc die cast. In a dry location, use to connect flexible metallic conduit (Greenfield or BX) to a steel outlet box or other metal enclosure. Steel, indoor or out. Use to join threaded Rigid or IMC conduit together. UL Listed.
Halex 96196 Rigid IMC Conduit Locknut Carlon E977LC-CAR Conduit Clamp Halex HX Flexible Screw-In Coupling
Steel with zinc plating. Indoor or outdoor applications. Use to secure Rigid or IMC conduit or various threaded fittings to a steel outlet box or other metal enclosure. Offers same chemical resistance as Carlon nonmetallic conduit for a complete, corrosion resistant system. UV resistant for use in direct sunlight. Use in accordance with conduit spacing requirements per NEC. Each clamp requires 2 screws, 2 nuts, and 2 washers. Gray clamps for standard conduit. Halex Screw-In Coupling, Flexible, Series: HX, 3/4 in Nominal, 1.12 in Hex, Die Cast Zinc, 2.09 in Length, CSA Certified, UL Listed, For use to join two pieces of flexible metallic conduit, indoor only
Halex 64327 Intermediate Rigid Conduit Nipple Halex 64331 Intermediate Rigid Conduit Nipple Halex 64341 Intermediate Rigid Conduit Nipple
Halex Conduit Nipple, Intermediate, Rigid, 3/4 in Nominal, Steel, 2 in Length, CSA Certified, UL Listed, For use to connect two steel outlet boxes or other metal enclosures; use to extend a length of threaded rigid or IMC conduit, indoor/outdoor Halex Conduit Nipple, Intermediate, Rigid, 1/2 in Nominal, Steel, Galvanized, 3 in Length, CSA Certified, UL Listed, For use to connect two steel outlet boxes or other metal enclosures; use to extend a length of threaded rigid or IMC conduit, indoor/outdoor Halex Conduit Nipple, Intermediate, Rigid, 1/2 in Nominal, Steel, 4 in Length, CSA Certified, UL Listed, For use to connect two steel outlet boxes or other metal enclosures; use to extend a length of threaded rigid or IMC conduit, indoor/outdoor
Halex 13305B Reducing Bushing Halex 13307B Reducing Bushing Halex 64361 Intermediate Rigid Conduit Nipple
Halex Reducing Bushing, 1 X 1/2 in Conduit, Rigid Conduit, Threaded End, Die Cast Steel, UL Listed, CSA Certified, For Dry Locations Applications Halex Reducing Bushing, 1 X 3/4 in Conduit, Rigid Conduit, Threaded End, Die Cast Steel, UL Listed, CSA Certified, For Dry Locations Applications Halex Conduit Nipple, Intermediate, Rigid, 1/2 in Nominal, Steel, 6 in Length, CSA Certified, UL Listed, For use to connect two steel outlet boxes or other metal enclosures; use to extend a length of threaded rigid or IMC conduit, indoor/outdoor
Halex 27251 Snap-In Bushing Thomas & Betts 700 Pipe Clamp Thomas And Betts Z703 1-25
Halex Snap-In Bushing, 1/2 in Trade, 0.72 in Inside Diameter, 0.99 in Outside Diameter, 0.36 in Thickness, Plastic, Snap-In Insulation, For Indoor Applications Thomas & Betts Pipe Clamp, Universal, Series: 700, 1 in Opening, 550 lb Load Capacity, Steel, ASTM A569, Electro Galvanized, Silver, 1-1/4 in Height, 14 ga Thickness, Includes: Bolt and Square Nut, OSHA Approved, 1.163 - 1.315 in Cable, For Suspend Electrical Pipes and Tubing From the Ceiling Pipe straps hold conduit and pipes in channel. They are inserted along the slot side of the channel and twisted into place. Pre-assembled with locking slot / hex head bolt. Gold-galvanized corrosion free finish.
Thomas And Betts Z703 1 1/4-10 Superstrut Superstrut 200 Flat Straight Bracket Splice Plate 7-1/4 in L Gardner Bender GCC-310 2-Hole Conduit Strap
Pipe straps hold conduit and pipes in channel. They are inserted along the slot side of the channel and twisted into place. Pre-assembled with locking slot / hex head bolt. Gold-galvanized corrosion free finish. Splices and supports conduit. Heavy-duty polyethylene, resists deterioration from UV rays and breakage from extreme cold. Enables secure fastening of plastic electrical conduit, schedule 40 PVC, copper tubing.
Thomas & Betts E977FC-CTN 2-Hole Conduit Clamp Halex 26154 1-Hole Snap-On Conduit Strap Halex HX EMT To Flexible Combination Coupling
Offers same chemical resistance as Carlon nonmetallic conduit for a complete, corrosion resistant system. UV resistant for use in direct sunlight. Use in accordance with conduit spacing requirements per NEC. Each clamp requires 2 screws, 2 nuts, and 2 washers. Gray clamps for standard conduit. Indoor or outdoor applications. To support EMT conduit. Halex Combination Coupling, EMT To Flexible, Series: HX, 1/2 in Nominal, Compression to Screw-In End, Die Cast Zinc, 1 in Width, CSA Certified, UL Listed, For use to join EMT conduit to flexible metallic conduit, indoor use only
Halex 27252 Snap-In Bushing Thomas And Betts Z702 21/2EG-10 Superstrut Pipe Clamp STRAP CBL 1HOLE OVAL SRVC ENT
Halex Snap-In Bushing, 3/4 in Trade, 0.95 in Inside Diameter, 1.22 in Outside Diameter, 0.36 in Thickness, Plastic, Snap-In Insulation, For Indoor Applications Pipe straps hold conduit and pipes in channel. They are inserted along the slot side of the channel and twisted into place. Pre-assembled with locking slot / hex head bolt. Steel, use to secure service entrance cable (SEU, SER) to wood, masonry or similar surface.
Halex 01925B IMC Conduit Locknut Halex 75400 Anti-Short Conduit Bushing Gardner Bender GGC-1508 Ground Clip
Use to secure Rigid or IMC conduit or various threaded fittings to a steel outlet box or other metal enclosure. Bulk packed. High dielectric plastic. Use to protect wire within flexible metallic conduit (Greenfield, BX). Insert one bushing at each end of conduit. UL Approved. No. 75400 - Fits cable range: 14/2, 14/3, 12/2 No. 75401 - Fits cable range: 14/4, 12/3, 6/1, 4/1. No. 75402 - Fits cable range: 12/4, 10/2, 10/3, 2/1. No. 75403 - Fits cable range: 10/4, 8/2, 8/3, 1/1. No. 75404 - Fits cable range: 8/4, 6/2, 6/3, 4/2, 4/3, 6/4. For aluminum or copper grounding wire zinc plated.
Eritech CP58 Acorn Standard Duty Ground Clamp Carlon E940LR/CTN Conduit Coupling Halex 75225 Insulated Conduit Bushing
Connects grounding wire to the grounding rod. UL and CSA Listed for 1/2" and 5/8" ground rods and number 4 rebar and accept a conductor range from number 10 solid to number 2 stranded. Safe, non-conductive. Schedule 40 non-metallic socket type coupling for joining Schedule 40 non-metallic conduit. Will not rust or corrode. RoHS Compliance, UL Listed. High impact thermoplastic. Flame retardant to 105 degrees C. Use with locknut to terminate threaded Rigid or IMC conduit to an outlet box. The rounded surface of the bushing prevents damage to wire insulation. Required by the NEC. UL Listed, CSA Approved.
Carlon UB9AD-CAR Standard Radius Conduit Elbow Carlon UA9AH-CAR Standard Radius Conduit Elbow Thomas & Betts E986D-CTN Type LB Rigid/IMC Conduit Body
For use with nonmetallic solvent weld fittings. Nonconductive, impact, corrosion and sunlight resistant. For use with nonmetallic solvent weld fittings. Nonconductive, impact, corrosion and sunlight resistant. Rigid non-metallic Type LB conduit body. For easy access and pulling of wires through conduit run. For use with Schedule 40 non-metallic solvent weld fittings. Will not rust or corrode. With textured lid and foam-in-place gasket. Hubs are not threaded. UL Listed, RoHS Compliance.
Carlon UA7AHR-CTN Standard Radius Conduit Elbow Carlon E985D-CTN Rigid Conduit Body Carlon E984D-CTN Rigid Conduit Body
For use with nonmetallic solvent weld fittings. Nonconductive, impact, corrosion and sunlight resistant. UL Listed E35297. For easy access and pulling of wires through conduit run. Textured lid, foam-in-place gasket. For use with Schedule 40/80 non-metallic solvent weld fittings. Will not rust or corrode. For easy access and pulling of wires through conduit run. For use with Schedule 40/80 non-metallic solvent weld fittings. Will not rust or corrode.
Halex 26166 2-Hole Snap-On Conduit Strap Halex 26156 1-Hole Snap-On Conduit Strap Halex 90452 Screw-In Coupling
To support EMT conduit where greater load bearing is required. Indoor or outdoor applications. Indoor or outdoor applications. To support EMT conduit. Zinc die cast. Use to join two pieces of flexible metallic conduit (Greenfield) together.
Halex 96402 Conduit Coupling Halex 64342 Intermediate Rigid Conduit Nipple Halex 20701 Rigid Conduit Chase Nipple
Steel, indoor or out. Use to join threaded Rigid or IMC conduit together. UL Listed. Halex Conduit Nipple, Intermediate, Rigid, 3/4 in Nominal, Steel, 4 in Length, CSA Certified, UL Listed, For use to connect two steel outlet boxes or other metal enclosures; use to extend a length of threaded rigid or IMC conduit, indoor/outdoor Halex Conduit Chase Nipple, Rigid, 1/2 in Nominal, Die Cast Zinc, 1.02 in Length X 0.68 in Width, CSA Certified, UL Listed, For use with a rigid coupling to terminate threaded conduit to a knockout box or enclosure, where space within the box is limited. used with a locknut to provide a short raceway between boxes or enclosures, indoor/outdoor
Halex 64362 Intermediate Rigid Conduit Nipple Thomas & Betts E943E5 Terminal Adapter Thomas And Betts Z703 1 1/2-10 Superstrut
Halex Conduit Nipple, Intermediate, Rigid, 3/4 in Nominal, Steel, 6 in Length, CSA Certified, UL Listed, For use to connect two steel outlet boxes or other metal enclosures; use to extend a length of threaded rigid or IMC conduit, indoor/outdoor Thomas & Betts Terminal Adapter, Series: E943E5, 3/4 in Conduit, Rigid Conduit, Male Thread X Socket End, SCH 40, PVC, 1-3/8 in Length, UL E 32447, RoHS Complaint, cUL Listed, For Adapting Non-Metallic Conduits to Boxes, Threaded Fittings and Metallic Systems Pipe straps hold conduit and pipes in channel. They are inserted along the slot side of the channel and twisted into place. Pre-assembled with locking slot / hex head bolt. Gold-galvanized corrosion free finish.
Thomas & Betts 700 Pipe Clamp Thomas & Betts 700 Pipe Clamp Superstrut 200 Series Angle Bracket Fitting
Thomas & Betts Pipe Clamp, Universal, Series: 700, 1-1/4 in Opening, 800 lb Load Capacity, Steel, ASTM A569, Electro Galvanized, Silver, 1-1/4 in Height, 14 ga Thickness, Includes: Bolt and Square Nut, OSHA Approved, 1.508 - 1.66 in Cable, For Suspend Electrical Pipes and Tubing From the Ceiling Thomas & Betts Pipe Clamp, Universal, Series: 700, 1-1/2 in Opening, 800 lb Load Capacity, Steel, ASTM A569, Electro Galvanized, Silver, 1-1/4 in Height, 14 ga Thickness, Includes: Bolt and Square Nut, OSHA Approved, 1.738 - 1.9 in Cable, For Suspend Electrical Pipes and Tubing From the Ceiling For use in metal framing applications. Manufactured from hot rolled carbon steel.
Thomas And Betts Z500-25 Superstrut Beam Clamp Eritech ZWP1J Grounding Pipe Clamp Carlon UA9AGB-CTN Standard Radius Conduit Elbow
For hanging rod, silver electroplated finish. Bolted water pipe clamps made of zinc die-cast. Wire range 8 sol. - 2 str. UL Listed. Connects grounding wire to the grounding rod. For use with nonmetallic solvent weld fittings. Nonconductive, impact, corrosion and sunlight resistant. Schedule 40. UL 651 Listed to the NEC by the ETL, UL Listed.
Halex 90662 Standard Water-Tight Connector Gardner Bender GGP-1502 Grounding Pigtail Halex 61230 2-Hole Conduit Strap
Die cast of high strength zinc alloy. Use to secure SE/SEU cable to a metal enclosure. Use to connect UF cable to a waterproof box with a threaded hub. AWG solid number 12 wire. 8" long with captured screw, other end bare fork terminal. Indoor or outdoor use. Use to secure Rigid or IMC conduit to wood, masonry or similar surfaces where greater load bearing is required. UL Listed, CSA Approved.
Fishock GRC-FS Ground Clamp Thomas & Betts E977GC-CTN 2-Hole Conduit Clamp Thomas & Betts E950GF-CTN Reducing Bushing
Helps to make a superior connection of ground wire to ground rod. Heavy duty construction for long usage. Offers same chemical resistance as Carlon nonmetallic conduit for a complete, corrosion resistant system. UV resistant for use in direct sunlight. Use in accordance with conduit spacing requirements per NEC. Each clamp requires 2 screws, 2 nuts, and 2 washers. Gray clamps for standard conduit. For connecting different sizes of conduit. Socket both ends, for reducing male Schedule 40/80 conduit runs or fittings to female. Non-conductive. Will not rust or corrode.
Carlon E950GE-CAR Reducing Conduit Bushing Halex 26164 2-Hole Snap-On Conduit Strap Carlon E987D-CTN Rigid Conduit Body
For connecting different sizes of conduit. Socket both ends, for reducing male Schedule 40/80 conduit runs or fittings to female. Non-conductive. Will not rust or corrode. To support EMT conduit where greater load bearing is required. Indoor or outdoor applications. For easy access and pulling of wires through conduit run. For use with Schedule 40/80 non-metallic solvent weld fittings. Will not rust or corrode. UL Listed.
Carlon LN43EA-CTN Liquidtight Straight Angle Conduit Connector Halex 11005B Conduit Elbow Halex 90661 Standard Water-Tight Connector
For flexible conduit. Non-metallic/non-conductive, corrosion resistant plastic. Zinc die cast. In a dry location, use to connect flexible metallic conduit (Greenfield or BX) to a steel outlet box or other metal enclosure. Die cast of high strength zinc alloy. Use to secure SE/SEU cable to a metal enclosure. Use to connect UF cable to a waterproof box with a threaded hub.
Halex 93591 Ground Clamp Halex 90703 Conduit Chase Nipple Halex 27362 Conduit Coupling
Connects grounding wire to the grounding rod. Zinc die cast. Indoor or outdoor applications. Use to terminate threaded conduit to a knockout box or enclosure, where space within the box is limited. Used with a locknut to provide a short raceway between boxes or enclosures. UL and CSA approved. Halex Conduit Coupling, 3/4 in Conduit, Liquid-Tight Conduit, Slip End, PVC, CSA Certified, UL Listed, For Weatherproof Outlet Boxes, Pool And Spa Equipment Motors, Central Air Conditioning Units and Various Other Electrical Enclosures And Hubs
Thomas & Betts E943D10 Terminal Adapter Gardner Bender GCC-410 2-Hole Conduit Strap Thomas And Betts Z702 3EG-10 Superstrut
Thomas & Betts Terminal Adapter, Series: E943D10, 1/2 in Conduit, Rigid Conduit, Male Thread X Socket End, SCH 40, PVC, 1-5/16 in Length, UL E 32447, RoHS Complaint, cUL Listed, For Adapting Non-Metallic Conduits to Boxes, Threaded Fittings and Metallic Systems Heavy-duty polyethylene, resists deterioration from UV rays and breakage from extreme cold. Enables secure fastening of plastic electrical conduit, schedule 40 PVC, copper tubing. Pipe straps hold conduit and pipes in channel. They are inserted along the slot side of the channel and twisted into place. Pre-assembled with locking slot / hex head bolt.
Carlon UA7AHB-CAR Standard Radius Conduit Elbow Halex 64312 Fully Threaded Conduit Nipple Thomas & Betts E950HGR Reducing Bushing
For use with nonmetallic solvent weld fittings. Nonconductive, impact, corrosion and sunlight resistant. UL Listed E35297. Made of steel, fully threaded. Indoor or outdoor. Use to connect two steel outlet boxes or other metal enclosures or to extend a length of threaded Rigid or IMC conduit. Bulk packed. For connecting different sizes of conduit. Socket both ends, for reducing male Schedule 40/80 conduit runs or fittings to female. Non-conductive. Will not rust or corrode.
Carlon E943L-CAR Terminal Adapter Gardner Bender 14-GRC Ground Clamp Carlon E983D-CTN Rigid IMC Conduit Body
Safe, non-conductive. For adapting schedule 40 non-metallic conduit to boxes, threaded fittings, metallic systems. Male threads on one end, socket end on the other. Will not rust or corrode. UL Listed, RoHS Compliance. Connects grounding wire to the grounding rod. For easy access and pulling of wires through conduit run. For use with Schedule 40/80 non-metallic solvent weld fittings. Will not rust or corrode.
Halex 75401 Anti-Short Conduit Bushing Halex 27250 Snap-In Bushing Halex 26073 Knock Out Seals
High dielectric plastic. Use to protect wire within flexible metallic conduit (Greenfield, BX). Insert one bushing at each end of conduit. UL Approved. No. 75400 - Fits cable range: 14/2, 14/3, 12/2 No. 75401 - Fits cable range: 14/4, 12/3, 6/1, 4/1. No. 75402 - Fits cable range: 12/4, 10/2, 10/3, 2/1. No. 75403 - Fits cable range: 10/4, 8/2, 8/3, 1/1. No. 75404 - Fits cable range: 8/4, 6/2, 6/3, 4/2, 4/3, 6/4. Use to protect non-metallic cable from damage when running cable through metal studs. Fits a variety of pre-punched metal stud openings. Use to cover exposed knock-out holes in steel outlet boxes and other metal enclosures.
Halex 75230 Insulated Conduit Bushing Halex 20581 Cable Connector Halex HX Multi-Piece Liquid-Tight Connector
High impact thermoplastic. Flame retardant to 105 degrees C. Use with locknut to terminate threaded Rigid or IMC conduit to an outlet box. The rounded surface of the bushing prevents damage to wire insulation. Required by the NEC. UL Listed, CSA Approved. In a dry location, use to connect AC (BX) cable to a steel outlet box or other metal enclosure. Suitable for #14-2 steel armored cable. Halex Liquid-Tight Connector, Multi-Piece, Series: HX, 3/8 in Nominal, Compression End, Straight, 1.18 in Hex, Die Cast Zinc, 1.32 in Length, CSA Certified, UL Listed, 1/2 in Male NPSM Hub, For use to connect flexible metallic or type b non-metallic liquid-tight conduit to a steel outlet box or other metal enclosure or hub, indoor/outdoor
Halex 19005 Short Radius Rigid IMC Conduit Elbow Thomas & Betts E940D10-UPC Conduit Coupling Halex HX Water-Tight UF Connector
Halex Conduit Elbow, Short Radius, Rigid, IMC, 90 deg, 1/2 in Conduit, Threaded End, Die Cast Zinc, CSA Certified, UL Listed, For use to connect rigid or IMC conduit to an outlet box where a close radius is desired, indoor/outdoor Thomas & Betts Conduit Coupling, 1/2 in Conduit, Rigid Conduit, Socket End, SCH 40, PVC, 0.728 in ID X 1-7/64 in OD Diameter, 1-1/2 in Length, cULus E 32447, RoHS Compliant Halex Water-Tight UF Connector, Series: HX, 1/2 in Nominal, Compression End, Straight, Die Cast Zinc, 1.2 in Length, Includes: (2) Insulating Conductors and (1) Bare, CSA Certified, UL Listed, 1/2 in Male NPSM Hub, 14/2 - 12/2 AWG Cable, For use to secure SE/SEU cable to a metal enclosure and to secure uf cable to a waterproof box with threaded hub
Superstrut 200 Flat Right Angle Bracket Corner Plate Carlon UA9AHB-CTN Standard Radius Rigid Conduit Elbow Gardner Bender GCC-220 2-Hole Conduit Strap
Splices and supports conduit. For use with nonmetallic solvent weld fittings. Nonconductive, impact, corrosion and sunlight resistant. Schedule 40. UL 651 Listed to the NEC by the ETL, UL Listed. Heavy-duty polyethylene, resists deterioration from UV rays and breakage from extreme cold. Enables secure fastening of plastic electrical conduit, schedule 40 PVC, copper tubing.
Gardner Bender GCC-510 2-Hole Conduit Strap Halex 64010 Conduit Coupling Carlon E942K-CAR Conduit Adapter
Heavy-duty polyethylene, resists deterioration from UV rays and breakage from extreme cold. Enables secure fastening of plastic electrical conduit, schedule 40 PVC, copper tubing. Steel, indoor or out. Use to join threaded Rigid or IMC conduit together. UL Listed. Safe, non-conductive. For adapting Schedule 40 non-metallic conduit to boxes, threaded fittings, metallic systems. Female threads one end, socket end on the other. Will not rust or corrode.
Halex 16205B Multi-Piece Liquid Tight Conduit Connector Carlon UB9AE-CAR Standard Radius Conduit Elbow Carlon E983E-CTN Rigid IMC Conduit Body
Multi-piece. Zinc die cast. Use to connect liquid-tight conduit to a steel outlet box or other metal enclosure or hub. UL Listed. Bulk packed. For use with nonmetallic solvent weld fittings. Nonconductive, impact, corrosion and sunlight resistant. For easy access and pulling of wires through conduit run. For use with Schedule 40/80 non-metallic solvent weld fittings. Will not rust or corrode.
Thomas & Betts E977HC-CTN 2-Hole Conduit Clamp Carlon E985E-CTN Rigid Conduit Body Carlon E984E-CTN Rigid Conduit Body
Offers same chemical resistance as Carlon nonmetallic conduit for a complete, corrosion resistant system. UV resistant for use in direct sunlight. Use in accordance with conduit spacing requirements per NEC. Each clamp requires 2 screws, 2 nuts, and 2 washers. Gray clamps for standard conduit. For easy access and pulling of wires through conduit run. Textured lid, foam-in-place gasket. For use with Schedule 40/80 non-metallic solvent weld fittings. Will not rust or corrode. For easy access and pulling of wires through conduit run. For use with Schedule 40/80 non-metallic solvent weld fittings. Will not rust or corrode.
Halex 91625 Multi-Piece Liquid Tight Compression Connector Halex 64405 Conduit Elbow Halex 75402 Anti-Short Conduit Bushing
Zinc die cast. Use to connect liquid-tight conduit to a steel outlet box, metal enclosure or hub. UL Approved. To connect EMT conduit together to allow for 90 degree bends. UL Approved. High dielectric plastic. Use to protect wire within flexible metallic conduit (Greenfield, BX). Insert one bushing at each end of conduit. UL Approved. No. 75400 - Fits cable range: 14/2, 14/3, 12/2 No. 75401 - Fits cable range: 14/4, 12/3, 6/1, 4/1. No. 75402 - Fits cable range: 12/4, 10/2, 10/3, 2/1. No. 75403 - Fits cable range: 10/4, 8/2, 8/3, 1/1. No. 75404 - Fits cable range: 8/4, 6/2, 6/3, 4/2, 4/3, 6/4.
Carlon Carflex LN20DA-CTN Liquidtight Conduit Elbow Carlon Carflex LN20EA-CTN Liquidtight Conduit Elbow Halex 91102 Pull Conduit Elbow
For flexible conduit. Non-metallic, Non-conductive, corrosion resistant plastic. For flexible conduit. Non-metallic, Non-conductive, corrosion resistant plastic. Zinc die cast. In a dry location, use to connect flexible metallic conduit (Greenfield or BX) to a steel outlet box or other metal enclosure.
Halex 27519 Hit Lock Cable Connectors Halex 27621 Multi-Piece Liquid Tight Straight Conduit Connector Halex 26074 Knock Out Seals
Fits NM Cable: #14/2, #14/3, #12/2, #10/2, #10/3. Snap-In, no screws or locknuts required. In a dry location, use to connect non-metallic sheathed cable to a steel outlet box or other metal enclosure. Design allows for two-step installation. Push into box and insert cable. UL Approved, CSA certified. Fitting will not rust or corrode. No disassembly required. Reusable, hand tightened nut. Use to connect type B non-metallic liquid-tight conduit to a weatherproof outlet box, pool/spa equipment motor, central air conditioning unit or various other electrical enclosures or hubs. UL Approved. Use to cover exposed knock-out holes in steel outlet boxes and other metal enclosures.
Carlon E950JHR Reducing Conduit Bushing Halex 20570 Combination Clamp Connector Halex 64313 Intermediate Rigid Conduit Nipple
For connecting different sizes of conduit. Socket both ends, for reducing male Schedule 40/80 conduit runs or fittings to female. Non-conductive. Will not rust or corrode. In a dry location, use to connect flexible metallic conduit, AC, MC, or NM cable to steel outlet box or other enclosure. Fits 1/2" knockout. Suitable For: #14/2 thru 12/3 with ground NM sheathed cable, #14-2 wire steel armored cable, 3/8" steel flexible metal conduit and steel interlocked metal clad cable 0.435-0.547" diameter. UL, CSA approved. Halex Conduit Nipple, Intermediate, Rigid, 1 in Nominal, Steel, Galvanized, 2 in Length, CSA Certified, UL Listed, For use to connect two steel outlet boxes or other metal enclosures; use to extend a length of threaded rigid or IMC conduit, indoor/outdoor
Halex 26214 1-Hole Corrosion Resistant Midget Strap Gardner Bender GCC-120 2-Hole Conduit Strap Thomas & Betts 700 Pipe Clamp
Halex Midget Strap, 1-Hole, Corrosion Resistant, 1/4 in Opening, Galvanized Steel, Electro Plated Zinc, 0.95 in Width, For Indoor/Outdoor Applications Heavy-duty polyethylene, resists deterioration from UV rays and breakage from extreme cold. Enables secure fastening of plastic electrical conduit, schedule 40 PVC, copper tubing. Thomas & Betts Pipe Clamp, Universal, Series: 700, 2 in Opening, 800 lb Load Capacity, Steel, ASTM A569, Electro Galvanized, Silver, 1-1/4 in Height, 14 ga Thickness, Includes: Bolt and Square Nut, OSHA Approved, 2.195 - 2.375 in Cable, For Suspend Electrical Pipes and Tubing From the Ceiling
Superstrut 200 Series Flat Straight Bracket Halex 36010 Ground Clamp Carlon UB9AF-CAR Standard Radius Conduit Elbow
Splices and supports conduit. Indoor or outdoor applications. Use to secure the grounding wire to a 1/2" through 1" pipe. UL Listed. Wire size fits #10 - #2 AWG. For use with nonmetallic solvent weld fittings. Nonconductive, impact, corrosion and sunlight resistant.
Thomas & Betts E986E-CTN Type LB Rigid/IMC Conduit Body Thomas & Betts E977JCR-CTN 2-Hole Conduit Clamp Halex 07012 Conduit Chase Nipple
Rigid non-metallic Type LB conduit body. For easy access and pulling of wires through conduit run. For use with Schedule 40 non-metallic solvent weld fittings. Will not rust or corrode. With textured lid and foam-in-place gasket. Hubs are not threaded. UL Listed, RoHS Compliance. Offers same chemical resistance as Carlon nonmetallic conduit for a complete, corrosion resistant system. UV resistant for use in direct sunlight. Use in accordance with conduit spacing requirements per NEC. Each clamp requires 2 screws, 2 nuts, and 2 washers. Gray clamps for standard conduit. Zinc die cast. Indoor or outdoor applications. Use to terminate threaded conduit to a knockout box or enclosure, where space within the box is limited. Used with a locknut to provide a short raceway between boxes or enclosures. UL and CSA approved.
Halex HX EMT To Flexible Combination Coupling Thomas & Betts E986F-CTN Type LB Rigid/IMC Conduit Body Carlon E983FR-CTN Rigid IMC Conduit Body
Halex Combination Coupling, EMT To Flexible, Series: HX, 3/4 in Nominal, Compression to Screw-In End, Die Cast Zinc, 1.19 in Width, CSA Certified, UL Listed, For use to join EMT conduit to flexible metallic conduit, indoor use only Rigid non-metallic Type LB conduit body. For easy access and pulling of wires through conduit run. For use with Schedule 40 non-metallic solvent weld fittings. Will not rust or corrode. With textured lid and foam-in-place gasket. Hubs are not threaded. UL Listed, RoHS Compliance. For easy access and pulling of wires through conduit run. For use with Schedule 40/80 non-metallic solvent weld fittings. Will not rust or corrode.
Carlon UA7AJ-CAR Standard Radius Conduit Elbow Halex 13410B Reducing Bushing Halex 27352 Terminal Adapter
For use with nonmetallic solvent weld fittings. Nonconductive, impact, corrosion and sunlight resistant. UL Listed E35297. Halex Reducing Bushing, 1-1/4 X 1 in Conduit, Rigid Conduit, Threaded End, Die Cast Steel, UL Listed, CSA Certified, For Dry Locations Applications Halex Terminal Adapter, 3/4 in Conduit, Male End, PVC, 5 in Length, For Indoor/Outdoor Applications
Gardner Bender GCC-610 2-Hole Conduit Strap LOCK NUT SEALER 1/2IN         Halex 05115 Twin Screw Clamp Connector
LOCK NUT SEALER 1/2IN
Our Price: $3.49
Heavy-duty polyethylene, resists deterioration from UV rays and breakage from extreme cold. Enables secure fastening of plastic electrical conduit, schedule 40 PVC, copper tubing. Secures rigid or IMC conduit, or threaded fittings to steel outlet boxes or other steel boxes where moisture proofing is needed. Steel with zinc plating, pre-molded seal on one side. Fits non metallic cable, flex cords, multi flex cords; fitting range .834 - 1.520 inches diameter SE cables 2 conductor 4/0. With 1/2" knockout. In a dry location, use to connect nonmetallic sheathed cable to a steel outlet box or other metal enclosure. UL Listed, meets CSA requirements. Tray boxed.
Halex 26075 Knock Out Seals Eritech CWP1J Grounding Pipe Clamp Carlon E987E-CTN Rigid Conduit Body
Use to cover exposed knock-out holes in steel outlet boxes and other metal enclosures. Bolted water pipe grounding clamp. UL listed. Made of corrosion-resistant copper alloy. For easy access and pulling of wires through conduit run. For use with Schedule 40/80 non-metallic solvent weld fittings. Will not rust or corrode. UL Listed.
Halex 27512 Hit Lock Cable Connectors Carlon UA7AJB-CAR Standard Radius Conduit Elbow Halex 07310 Compression Standard Water-Tight Connector
Fits NM Cable: #14/2, #14/3, #12/2, #10/2, #10/3. Snap-In, no screws or locknuts required. In a dry location, use to connect non-metallic sheathed cable to a steel outlet box or other metal enclosure. Design allows for two-step installation. Push into box and insert cable. UL Approved, CSA certified. For use with nonmetallic solvent weld fittings. Nonconductive, impact, corrosion and sunlight resistant. UL Listed E35297. Die cast of high strength zinc alloy. Use to secure SE/SEU cable to a metal enclosure. Use to connect UF cable to a waterproof box with a threaded hub.
Halex HX Multi-Piece Liquid-Tight Connector Teddico/BWF 500V Thinwall Rigid Conduit Entrance Elbow Halex 64012 Conduit Coupling
Halex Liquid-Tight Connector, Multi-Piece, Series: HX, 3/8 in Nominal, Compression End, 90 deg, 1.66 in Hex, Die Cast Zinc, 1.45 in Length, CSA Certified, UL Listed, 1/2 in Male NPSM Hub, For use to connect flexible metallic or type b non-metallic liquid-tight conduit to a steel outlet box or other metal enclosure or hub, indoor/outdoor Teddico/BWF Conduit Entrance Elbow, Thinwall, SLB, 1/2 in Hub, Rigid Conduit, Threaded Installation, Die Cast Aluminum, Gray, Powder Coated, Includes: Cover and Screw, CSA Certified, UL Listed, For connecting conduit sections, making bends in conduit runs as pull outlets, to provide openings for making splices and taps in conductors Steel, indoor or out. Use to join threaded Rigid or IMC conduit together. UL Listed.
Halex 27361 Conduit Coupling Thomas & Betts E984F-CAR Rigid Conduit Body Thomas & Betts E985F-CAR Rigid Conduit Body
Halex Conduit Coupling, 1/2 in Conduit, Liquid-Tight Conduit, Slip End, PVC, CSA Certified, UL Listed, For Weatherproof Outlet Boxes, Pool And Spa Equipment Motors, Central Air Conditioning Units and Various Other Electrical Enclosures And Hubs Thomas & Betts Conduit Body, LL, 1 in Hub, Rigid Conduit, Foam, Non-Threaded Installation, 6-9/32 in Length, 2-1/32 in Width, PVC, CSA Certified, UL Listed Thomas & Betts Conduit Body, LR, 1 in Hub, Rigid Conduit, Foam, Non-Threaded Installation, 6-9/32 in Length, 2-1/32 in Width, PVC, CSA Certified, UL Listed
Teddico/BWF 181V Clamp Service Entrance Head Carlon Z703 2 Pipe Clamp Superstrut ZCM1001/4-10 Cone Nut
Teddico/BWF Service Entrance Head, Clamp, 3/4 in Trade, Gray Pipe straps hold conduit and pipes in channel. They are inserted along the slot side of the channel and twisted into place. Pre-assembled with locking slot / hex head bolt. Gold-galvanized corrosion free finish. Superstrut Cone Nut, 1/4 in Nominal, Nylon Cone, Steel Nut, Galvanized, Gold, For Superstrut Metal Framing and Hanger System
WASHER REDUCING 2X1IN         WASHER REDUCING 2X1-1/4IN     Halex 26152 1-Hole Snap-On Conduit Strap
WASHER REDUCING 2X1IN
Our Price: $3.79
Use to reduce the size of the conduit hole knockout opening in a steel outlet box or other metal enclosure. Must use one inside the enclosure opening and one on the outside. UL Listed, CSA Approved. Use to reduce the size of the conduit hole knockout opening in a steel outlet box or other metal enclosure. Must use one inside the enclosure opening and one on the outside. UL Listed, CSA Approved. Indoor or outdoor applications. To support EMT conduit.
Carlon E942L-CAR Conduit Adapter Halex 26161 2-Hole Snap-On Conduit Strap Carlon E990DR-CAR Access Pull Standard Radius Conduit Elbow
Safe, non-conductive. For adapting Schedule 40 non-metallic conduit to boxes, threaded fittings, metallic systems. Female threads one end, socket end on the other. Will not rust or corrode. To support EMT conduit where greater load bearing is required. Indoor or outdoor applications. Access pull point for cable in tight radius. Allows conduit changes in direction. Won't rust or corrode. Gasket included.
Carlon UA9AJ-CAR Standard Radius Conduit Elbow Halex 26151 1-Hole Snap-On Conduit Strap Halex 58305 Rigid Threaded Conduit Body with Cover and Gasket
For use with nonmetallic solvent weld fittings. Nonconductive, impact, corrosion and sunlight resistant. Indoor or outdoor applications. To support EMT conduit. Aluminum, indoors or outdoors. Use to gain access to the interior of a raceway for wire pulling, splicing (with limitations as specified by the NEC), and maintenance. With cover and gasket. UL Approved. Tray boxed.
Halex 58405 Rigid Threaded Conduit Body with Cover and Gasket Halex 58605 Rigid Threaded Conduit Body with Cover and Gasket Halex 58905 Rigid Threaded Conduit Body with Cover and Gasket
Copper-free die cast aluminum. Indoors or outdoors. Use to gain access to the interior of a raceway for wire pulling, splicing (with limitations as specified by the NEC), and maintenance. With cover and gasket. UL Approved. Tray boxed. Aluminum, indoor or outdoor. Use to gain access to the interior of a raceway for wire pulling, splicing (with limitations as specified by the NEC), and maintenance. With cover and gasket. UL Approved. Aluminum, indoor or outdoor. Use to gain access to the interior of a raceway for wire pulling, splicing (with limitations as specified by the NEC), and maintenance. With cover and gasket. UL Approved. Tray boxed.
Halex 94105 Pull Conduit Elbow with Neoprene Gasket Carlon E987F-CAR Rigid Conduit Body Halex 26141 Flat Drive Strap
Zinc die cast. Indoors or outdoors. Use as a wire pulling elbow to facilitate wire pulling through a sharp bend in a run of threaded Rigid or IMC conduit. Removable cover provides easy access to wiring. UL Approved. Bulk packed. For easy access and pulling of wires through conduit run. For use with Schedule 40/80 non-metallic solvent weld fittings. Will not rust or corrode. UL Listed. Indoors or outdoors. To secure EMT conduit to a wood or masonry surface.
Halex 27622 Multi-Piece Liquid Tight Straight Conduit Connector Carlon UA9AJB-CAR Standard Radius Conduit Elbow Halex 20440 Flexible Screw-In Connector
Fitting will not rust or corrode. No disassembly required. Reusable, hand tightened nut. Use to connect type B non-metallic liquid-tight conduit to a weatherproof outlet box, pool/spa equipment motor, central air conditioning unit or various other electrical enclosures or hubs. UL Approved. For use with nonmetallic solvent weld fittings. Nonconductive, impact, corrosion and sunlight resistant. Schedule 40. UL 651 Listed to the NEC by the ETL, UL Listed. Halex Screw-In Connector, Flexible, 1/2 in Nominal, 0.92 in Hex, Die Cast Zinc, 1.38 in Length, CSA Certified, UL Listed, For use to connect flexible metallic conduit to steel outlet box, load center or other metal enclosure, indoor use only
Halex 93592 Ground Clamp Halex 61820B IMC Sealer Locknut Carlon E995GR Meter Offset
Connects grounding wire to the grounding rod. Secures rigid or IMC conduit, or threaded fittings to steel outlet boxes or other steel boxes where moisture proofing is needed. Steel with zinc plating, pre-molded seal on one side. For installation from Schedule 40/80 non-metallic conduit runs into meter box. Will not rust or corrode.
Carlon E990ER-CAR Access Pull Standard Radius Conduit Elbow Halex 07015 Conduit Chase Nipple Halex 64407 Conduit Elbow
Access pull point for cable in tight radius. Allows conduit changes in direction. Won't rust or corrode. Gasket included. Zinc die cast. Indoor or outdoor applications. Use to terminate threaded conduit to a knockout box or enclosure, where space within the box is limited. Used with a locknut to provide a short raceway between boxes or enclosures. UL and CSA approved. To connect EMT conduit together to allow for 90 degree bends. UL Approved.
Halex 58005 Standard Weatherhead Service Entrance Cap Halex 20510 Twin Screw Clamp Connector Thomas And Betts ZA1001/4EG-10 Superstrut
Aluminum die cast. Indoor or outdoor applications. Use in an overhead service entrance. Mounts on top of EMT, Rigid or IMC conduit. Serves as a connecting point for the service entrance wires. UL Listed meets CSA requirements. Tray boxed. Fits 1/2" knockout, non-metallic cable numbers 14/2, 12/2, 12/3 AWG or 2 number 14/2 AWG or flex cord .300 to .560 inches diameter. In a dry location, use to connect nonmetallic sheathed cable to a steel outlet box or other metal enclosure. UL, Listed, meets CSA requirements. For use with 'A' and 'C' series channel and inserts.
Thomas And Betts Z502-10 Superstrut Beam Clamp Halex 05120 Twin Screw Clamp Connector Halex 04010 Offset Nipple
For hanging rod, silver electroplated finish. Fits non metallic cable, flex cords, multi flex cords fitting range 1.085 - 1.520 inches diameter. With 1/2" knockout. In a dry location, use to connect nonmetallic sheathed cable to a steel outlet box or other metal enclosure. UL Listed, meets CSA requirements. Tray boxed. Zinc die cast. Use as an offset connector between two enclosures. Offsets the axis of the raceway 3/4". UL Approved.
Halex 64015 Conduit Coupling Carlon E995J-CTN Meter Offset Halex 16207B Multi-Piece Liquid Tight Conduit Connector
Steel, indoor or out. Use to join threaded Rigid or IMC conduit together. UL Listed. For installation from Schedule 40/80 non-metallic conduit runs into meter box. Will not rust or corrode. Multi-piece. Zinc die cast. Use to connect liquid-tight conduit to a steel outlet box or other metal enclosure or hub. UL Listed. Bulk packed.
Carlon UB9AG-CAR Standard Radius Conduit Elbow Thomas & Betts E986GR Type LB Rigid/IMC Conduit Body Halex 60416 Light Duty Wire Holder
For use with nonmetallic solvent weld fittings. Nonconductive, impact, corrosion and sunlight resistant. Rigid non-metallic Type LB conduit body. For easy access and pulling of wires through conduit run. For use with Schedule 40 non-metallic solvent weld fittings. Will not rust or corrode. With textured lid and foam-in-place gasket. Hubs are not threaded. UL Listed, RoHS Compliance. Used indoors or outdoors to secure incoming service entrance wires. Reinforced. Porcelain and steel. Tray box.
Halex 20491 Combination Coupling Halex 27691 Liquid Tight Conduit Elbow Halex 59505 Service Entrance Elbow
Use to joint EMT conduit to flexible metal conduit. Die cast zinc. UL Approved, CSA Certified. Indoors or outdoors, fitting will not rust or corrode. No disassembly required, just hand-tighten nut. Reusable. Use to connect type B non-metallic liquid-tight conduit to a weatherproof outlet box, pool/spa equipment motor, central air conditioning unit or various other electrical enclosures or hubs. UL Approved. Copper-free die cast aluminum. Use to gain access to the interior of a raceway for wire pulling, inspection and maintenance. UL Approved. Tray boxed.
Carlon E990DER-CAR Pull Elbow With Reducer Bushing Halex 20512 Twin Screw Clamp Connector Teddico/BWF 300-CGV Thinwall Conduit Body Assembly
Access pull point for cable in tight radius. Allows conduit changes in direction. Won't rust or corrode. Gasket included. Fits non metallic cable, such as Romex, number 14/2 round, number 12/3-8/3 AWG or flex cord .460 to .720 inches diameter. In a dry location, use to connect nonmetallic sheathed cable to a steel outlet box or other metal enclosure. UL Listed, meets CSA requirements. Teddico/BWF Conduit Body Assembly, Thinwall, C, 1/2 in Hub, 2 Hubs, Side Access Opening, Straight Hub, Stamped Aluminum Cover, Threaded Installation, Die Cast Aluminum, Neoprene Gasket, Gray, Includes: Cover and Gasket, UL 514B, UL E121488, CSA C22.2 No. 18, CSA LR57925, NEMA FB-1, NEC Article 348, For Wire Pulling
Teddico/BWF 600-CGV Thinwall Conduit Body Assembly Halex 64105 Conduit Elbow Halex 58007 Clamp On Weatherhead Service Entrance Cap
Teddico/BWF Conduit Body Assembly, Thinwall, LB, 1/2 in Hub, Back Side Access Opening, Stamped Aluminum Cover, Threaded Installation, 15-1/2 in Length, 8-1/2 in Width, 5-3/4 in Depth, Die Cast Aluminum, Neoprene Gasket, Gray, Includes: Cover and Gasket, UL 514B, UL E121488, CSA C22.2 No. 18, CSA LR57925, NEMA FB-1, NEC Article 348, For Wire Pulling Use to allow a 90 degree change of direction in a run of Rigid or IMC conduit. UL Listed. Aluminum die cast. Indoor or outdoor applications. Use in an overhead service entrance. Mounts on top of EMT, Rigid or IMC conduit. Serves as a connecting point for the service entrance wires. UL Listed meets CSA requirements. Tray boxed.
Halex 36110 Ground Clamp Halex 26162 2-Hole Snap-On Conduit Strap Thomas And Betts ZA1003/8EG-10 Superstrut
Indoor or outdoor. Wire size fits number 8 - number 4 AWG. Use to secure the grounding wire to a 1/2" through 1" pipe. Bronze, bagged. UL Listed. To support EMT conduit where greater load bearing is required. Indoor or outdoor applications. For use with 'A' and 'C' series channel and inserts.
Thomas And Betts ZU501-10 Superstrut Beam Clamp Steel City ZCK535-10 Armored Cable Hanger Clip Halex 94107 Pull Conduit Elbow
For channel. 3-1/16". Flexible conduit hanger from drop wire, #8-#12 wire, .433-.535 O.D. cable. Zinc die cast. Indoors or outdoors. Use as a wire pulling elbow to facilitate wire pulling through a sharp bend in a run of threaded Rigid or IMC conduit. Removable cover provides easy access to wiring. UL Approved. Bulk packed.
Halex 21642 Box Spacer Carlon E998E-CAR Service Entrance Cap Halex 91627 Multi-Piece Liquid Tight Conduit Connector
Die cast of high strength corrosion resistant zinc alloy. Locknut is reversible. It is designed to cut through protective coatings on boxes and enclosures to assure ground continuity. Use as a raceway between two steel outlet boxes or other metal enclosures. UL and CSA Listed. Safe, non-conductive. To bring overhead wiring from outside into conduit run. Will not rust or corrode. For use with Schedule 40/80 non-metallic solvent weld fittings. Zinc die cast. Use to connect liquid-tight conduit to a steel outlet box, metal enclosure or hub. UL Approved.
Halex 58805 Rigid Threaded Conduit Body with Cover and Gasket Halex 26076 Knock Out Seals Halex 27351 Terminal Adapter
Copper-free die cast aluminum. Indoors or outdoors. Use to gain access to the interior of a raceway for wire pulling, splicing (with limitations as specified by the NEC), and maintenance. UL Approved. Tray boxed. Use to cover exposed knock-out holes in steel outlet boxes and other metal enclosures. Halex Terminal Adapter, 1/2 in Conduit, Male End, PVC, 10 in Length, For Indoor/Outdoor Applications
Thomas And Betts ZA1001/2EG-10 Superstrut Carlon E998F-CAR Standard Weatherhead Service Entrance Cap Halex 08212B Compression Standard Water-Tight Connector
For use with 'A' and 'C' series channel and inserts. Safe, non-conductive. To bring overhead wiring from outside into conduit run. Will not rust or corrode. For use with Schedule 40/80 non-metallic solvent weld fittings. Die cast of high strength zinc alloy. Use to secure SE/SEU cable to a metal enclosure. Use to connect UF cable to a waterproof box with a threaded hub.
Halex 36019 Ground Clamp Halex 26142 Flat Drive Strap Halex 26571 Flexible MC Snap-In Connector
Indoor or outdoor applications. Use to secure the grounding wire to a 1/2" through 1" pipe. UL Listed. Wire size fits #10 - #2 AWG. Indoors or outdoors. To secure EMT conduit to a wood or masonry surface. Halex MC Snap-In Connector, Flexible, 3/8 in Nominal, Steel, Includes: Insulating Bushing, CSA Certified, UL Listed, For use to connect aluminum or steel ac, aluminum mc, and steel flexible metal conduit, indoor use only
Teddico/BWF 100-CGV Thinwall Conduit Body Assembly Teddico/BWF 200-CGV Thinwall Conduit Body Assembly Teddico/BWF 501V Thinwall Rigid Conduit Entrance Elbow
Teddico/BWF Conduit Body Assembly, Thinwall, LR, 1/2 in Hub, 2 Hubs, Right Side Access Opening, 90 deg Hub, Stamped Aluminum Cover, Threaded Installation, 4.3 in Length, 2.4 in Width, 1.3 in Depth, Die Cast Aluminum, Neoprene Gasket, Gray, Includes: Cover and Gasket, UL 514B, UL E121488, CSA C22.2 No. 18, CSA LR57925, NEMA FB-1, NEC Article 348 Teddico/BWF Conduit Body Assembly, Thinwall, LL, 1/2 in Hub, 2 Hubs, Left Side Access Opening, 90 deg Hub, Stamped Aluminum Cover, Threaded Installation, 4.3 in Length, 2.4 in Width, 1.3 in Depth, Die Cast Aluminum, Neoprene Gasket, Gray, Includes: Cover and Gasket, UL 514B, UL E121488, CSA C22.2 No. 18, CSA LR57925, NEMA FB-1, NEC Article 348 Teddico/BWF Conduit Entrance Elbow, Thinwall, SLB, 3/4 in Hub, Rigid Conduit, Threaded Installation, Die Cast Aluminum, Gray, Powder Coated, Includes: Cover and Screw, CSA Certified, UL Listed, For connecting conduit sections, making bends in conduit runs as pull outlets, to provide openings for making splices and taps in conductors
Teddico/BWF 700-CGV Thinwall Conduit Body Assembly Halex 64320 Conduit Nipple Steel City R Threaded Rod
Teddico/BWF Conduit Body Assembly, Thinwall, T, 1/2 in Hub, 3 Hubs, Side Access Opening, Tee Hub, Stamped Aluminum Cover, Threaded Installation, Die Cast Aluminum, Neoprene Gasket, Gray, Includes: Cover and Gasket, UL 514B, UL E121488, CSA C22.2 No. 18, CSA LR57925, NEMA FB-1, NEC Article 348, For Wire Pulling Made of steel, fully threaded. Indoor or outdoor. Use to connect two steel outlet boxes or other metal enclosures or to extend a length of threaded Rigid or IMC conduit. Bulk packed. Framing and hanging applications. Free-running, corrosion resistant, burr-free.
Superstrut 200 Series Square Conduit Washer Superstrut 200 Series Square Conduit Washer Carlon E983GR-CAR Rigid IMC Conduit Body
GoldGalv finish. GoldGalv finish. For easy access and pulling of wires through conduit run. For use with Schedule 40/80 non-metallic solvent weld fittings. Will not rust or corrode.
Square D PK7GTACP Ground Bar Kits Carlon UAFAD Flexible Conduit Elbow Teddico/BWF 301-CGV Thinwall Conduit Body Assembly
Used in load centers, CSED devices and NQOD and NF panel boards. Each terminal accepts (1) #14 - #4 copper wire or (1) #12 - #4 aluminum wire, (2) #14 - #12 copper wire or (2) #12 - #10 aluminum wire. NOTE - Consult local code for correct application of ground bar kit for service entrance equipment. ANSI Certified and UL Listed. Made of a highly durable plastic (PVC) compound making the product nonmetallic and safe to install. Elbow is non-corrosive, rustproof, and easily pliable. Good for those applications that requires change of direction. UL listed. Teddico/BWF Conduit Body Assembly, Thinwall, C, 3/4 in Hub, 2 Hubs, Side Access Opening, Straight Hub, Stamped Aluminum Cover, Threaded Installation, 15-1/2 in Length, 8-1/2 in Width, 5-3/4 in Depth, Die Cast Aluminum, Neoprene Gasket, Gray, Includes: Cover and Gasket, UL 514B, UL E121488, CSA C22.2 No. 18, CSA LR57925, NEMA FB-1, NEC Article 348
Teddico/BWF 601-CGV Thinwall Conduit Body Assembly Carlon Carflex LN43FA-CAR 1-Piece Straight Conduit Connector Carlon E977DC25-UPC Conduit Clamp
Teddico/BWF Conduit Body Assembly, Thinwall, LB, 3/4 in Hub, Back Side Access Opening, Stamped Aluminum Cover, Threaded Installation, 15-1/2 in Length, 8-1/2 in Width, 5-3/4 in Depth, Die Cast Aluminum, Neoprene Gasket, Gray, Includes: Cover and Gasket, UL 514B, UL E121488, CSA C22.2 No. 18, CSA LR57925, NEMA FB-1, NEC Article 348, For Wire Pulling For flexible conduit. Non-metallic/non-conductive, corrosion resistant plastic. Offers same chemical resistance as Carlon nonmetallic conduit for a complete, corrosion resistant system. UV resistant for use in direct sunlight. Use in accordance with conduit spacing requirements per NEC. Each clamp requires 2 screws, 2 nuts, and 2 washers. Gray clamps for standard conduit.
Carlon E998G-CAR Service Entrance Cap Halex 16905B Multi-Piece Liquid Tight Conduit Elbow Thomas & Betts E986HR Type LB Rigid/IMC Conduit Body
Safe, non-conductive. To bring overhead wiring from outside into conduit run. Will not rust or corrode. For use with Schedule 40/80 non-metallic solvent weld fittings. Multi-piece, zinc die cast. Use to connect liquid-tight conduit to a steel outlet box or other metal enclosure or hub. UL Listed. Rigid non-metallic Type LB conduit body. For easy access and pulling of wires through conduit run. For use with Schedule 40 non-metallic solvent weld fittings. Will not rust or corrode. With textured lid and foam-in-place gasket. Hubs are not threaded. UL Listed, RoHS Compliance.
Halex 58607 Rigid Threaded Conduit Body with Cover and Gasket Eritech CWP1JU Grounding Pipe Clamp Halex 58907 Rigid Threaded Conduit Body with Cover and Gasket
Aluminum, indoor or outdoor. Use to gain access to the interior of a raceway for wire pulling, splicing (with limitations as specified by the NEC), and maintenance. With cover and gasket. UL Approved. Bolted water pipe clamps made from high-strength corrosion-resistant copper alloy. Connects grounding wire to the grounding rod. Range 10 solid - 2 stranded. UL Listed. Aluminum, indoor or outdoor. Use to gain access to the interior of a raceway for wire pulling, splicing (with limitations as specified by the NEC), and maintenance. With cover and gasket. UL Approved. Tray boxed.
Halex 20441 Flexible Screw-In Connector Halex 64107 Conduit Elbow Halex 95212B Insulated Metallic Grounding Conduit Bushing with Lug
Halex Screw-In Connector, Flexible, 1/2 in Nominal, 0.92 in Hex, Die Cast Zinc, 1.38 in Length, CSA Certified, UL Listed, For use to connect flexible metallic conduit to steel outlet box, load center or other metal enclosure, indoor use only Use to allow a 90 degree change of direction in a run of Rigid or IMC conduit. UL Listed. Zinc die cast. Rounded surface prevents damage to insulation. Thermoplastic liner rated at 150 degree F. Indoor or outdoor use. Use with locknut to terminate service conduit to a cabinet. Lug provided for bonding jumper to a neutral bus bar. UL Listed, CSA Approved.
Halex 58307 Rigid Threaded Conduit Body with Cover and Gasket Halex 64410 Conduit Elbow Halex 04012 Offset Nipple
Aluminum, indoors or outdoors. Use to gain access to the interior of a raceway for wire pulling, splicing (with limitations as specified by the NEC), and maintenance. With cover and gasket. UL Approved. Tray boxed. To connect EMT conduit together to allow for 90 degree bends. UL Approved. Zinc die cast. Use as an offset connector between two enclosures. Offsets the axis of the raceway 3/4". UL Approved.
Thomas & Betts E977NEC-CTN 1-Piece Conduit Clamp Thomas & Betts E977NDC-CTN 1-Piece Conduit Clamp Halex 58407 Rigid Threaded Conduit Body with Cover and Gasket
Drill  5/16'' hole with masonry bit and tap in with hammer. Drill  5/16'' hole with masonry bit and tap in with hammer. Copper-free die cast aluminum. Indoors or outdoors. Use to gain access to the interior of a raceway for wire pulling, splicing (with limitations as specified by the NEC), and maintenance. With cover and gasket. UL Approved. Tray boxed.
Teddico/BWF 101-CGV Thinwall Conduit Body Assembly Teddico/BWF 201-CGV Thinwall Conduit Body Assembly Teddico/BWF 701-CGV Thinwall Conduit Body Assembly
Teddico/BWF Conduit Body Assembly, Thinwall, LR, 3/4 in Hub, 2 Hubs, Right Side Access Opening, 90 deg Hub, Stamped Aluminum Cover, Threaded Installation, Die Cast Aluminum, Neoprene Gasket, Gray, Includes: Cover and Gasket, UL 514B, UL E121488, CSA C22.2 No. 18, CSA LR57925, NEMA FB-1, NEC Article 348, For Wire Pulling Teddico/BWF Conduit Body Assembly, Thinwall, LL, 3/4 in Hub, 2 Hubs, Left Side Access Opening, 90 deg Hub, Stamped Aluminum Cover, Threaded Installation, 5 in Length, 2.6 in Width, 1-1/2 in Depth, Die Cast Aluminum, Neoprene Gasket, Gray, Includes: Cover and Gasket, UL 514B, UL E121488, CSA C22.2 No. 18, CSA LR57925, NEMA FB-1, NEC Article 348 Teddico/BWF Conduit Body Assembly, Thinwall, T, 3/4 in Hub, 3 Hubs, Side Access Opening, Tee Hub, Stamped Aluminum Cover, Threaded Installation, Die Cast Aluminum, Neoprene Gasket, Gray, Includes: Cover and Gasket, UL 514B, UL E121488, CSA C22.2 No. 18, CSA LR57925, NEMA FB-1, NEC Article 348, For Wire Pulling
26351 RIGID CMPRSN CON STL1/2I Superstrut ZCM1003/8-10 Cone Nut Superstrut ZCM1001/2-10 Cone Nut
Use to join threadless Rigid or IMC conduit to a steel outlet box or other metal enclosure. Concrete-tight. UL, CSA. Superstrut Cone Nut, 3/8 in Nominal, Nylon Cone, Steel Nut, Galvanized, Gold, For Superstrut Metal Framing and Hanger System Superstrut Cone Nut, 1/2 in Nominal, Nylon Cone, Steel Nut, Galvanized, Gold, For Superstrut Metal Framing and Hanger System
Thomas And Betts Z503-5 Superstrut Beam Clamp Halex 07020 Conduit Chase Nipple Halex 63299 Ground Screw
For hanging rod, silver electroplated finish. Zinc die cast. Indoor or outdoor applications. Use to terminate threaded conduit to a knockout box or enclosure, where space within the box is limited. Used with a locknut to provide a short raceway between boxes or enclosures. UL and CSA approved. Indoor or outdoor applications. Use to ground a wiring device to a steel outlet box. Green color.
GE TC100P Rainproof Conduit Hub GE TC125P Rainproof Conduit Hub GE TC150P Rainproof Conduit Hub
For outdoor enclosures with removable closing caps. For outdoor enclosures with removable closing caps. For outdoor enclosures with removable closing caps.
GE TC200P Rainproof Conduit Hub Halex 61212B 2-Hole Conduit Strap Carlon UB9AH-CAR Standard Radius Conduit Elbow
For outdoor enclosures with removable closing caps. Indoor or outdoor use. Use to secure Rigid or IMC conduit to wood, masonry or similar surfaces where greater load bearing is required. UL Listed, CSA Approved. For use with nonmetallic solvent weld fittings. Nonconductive, impact, corrosion and sunlight resistant.
Halex 91695 Multi-Piece Liquid Tight Conduit Elbow Halex 58010 Clamp On Weatherhead Service Entrance Cap Carlon E977EC20-UPC Conduit Clamp
Multi-piece, zinc die cast. Use to connect liquid-tight conduit to a steel outlet box or other metal enclosure or hub. UL Listed. Aluminum die cast. Indoor or outdoor applications. Use in an overhead service entrance. Mounts on top of EMT, Rigid or IMC conduit. Serves as a connecting point for the service entrance wires. UL Listed meets CSA requirements. Tray boxed. Offers same chemical resistance as Carlon nonmetallic conduit for a complete, corrosion resistant system. UV resistant for use in direct sunlight. Use in accordance with conduit spacing requirements per NEC. Each clamp requires 2 screws, 2 nuts, and 2 washers. Gray clamps for standard conduit.
Halex 27692 Liquid Tight Conduit Elbow Halex 59507 Service Entrance Elbow Halex 96361 Concrete-Tight Conduit Coupling
Indoors or outdoors, fitting will not rust or corrode. No disassembly required, just hand-tighten nut. Reusable. Use to connect type B non-metallic liquid-tight conduit to a weatherproof outlet box, pool/spa equipment motor, central air conditioning unit or various other electrical enclosures or hubs. UL Approved. Copper-free die cast aluminum. Use to gain access to the interior of a raceway for wire pulling, inspection and maintenance. UL Approved. Tray boxed. Halex Conduit Coupling, Concrete-Tight, 1/2 in Conduit, IMC, Rigid Conduit, Compression End, Steel, Galvanized, 1.76 in Length, UL Listed, CSA Certified, 1.17 in Width, For Indoor Applications
Carlon E987H-CAR Rigid Conduit Body Siemens EC38599 Type RX Conduit Hub Halex 64412 Conduit Elbow
For easy access and pulling of wires through conduit run. For use with Schedule 40/80 non-metallic solvent weld fittings. Will not rust or corrode. UL Listed. For use on all Siemans and Murry single position meter sockets. To connect EMT conduit together to allow for 90 degree bends. UL Approved.
Halex 99526 Insulated Metallic Grounding Conduit Bushing with Lug Halex 61205B 2-Hole Conduit Strap Carlon UB9AJ-CAR Standard Radius Conduit Elbow
Zinc die cast. Rounded surface prevents damage to insulation. Thermoplastic liner rated at 150 degree F. Indoor or outdoor use. Use with locknut to terminate service conduit to a cabinet. Lug provided for bonding jumper to a neutral bus bar. UL Listed, CSA Approved. Indoor or outdoor use. Use to secure Rigid or IMC conduit to wood, masonry or similar surfaces where greater load bearing is required. UL Listed, CSA Approved. For use with nonmetallic solvent weld fittings. Nonconductive, impact, corrosion and sunlight resistant.
Carlon E983H-CAR Rigid IMC Conduit Body Carlon E998H-CAR Standard Weatherhead Service Entrance Cap Halex 57499 Oval Standard Service Cable Cap IMC
For easy access and pulling of wires through conduit run. For use with Schedule 40/80 non-metallic solvent weld fittings. Will not rust or corrode. Safe, non-conductive. To bring overhead wiring from outside into conduit run. Will not rust or corrode. For use with Schedule 40/80 non-metallic solvent weld fittings. Copper-free aluminum die cast. Indoor or outdoor applications. Use in overhead services that utilize SEU cable. Tray boxed.
Halex 58012 Clamp On Weatherhead Service Entrance Cap Cutler-Hammer GBK10P Ground Bar Kits Carlon UA9AK-CAR Standard Radius Conduit Elbow
Aluminum die cast. Indoor or outdoor applications. Use in an overhead service entrance. Mounts on top of EMT, Rigid or IMC conduit. Serves as a connecting point for the service entrance wires. UL Listed meets CSA requirements. Tray boxed. Bar wire holes are suitable for (1) #14-4 or up to (3) #14-10 aluminum or copper wire. Multiple wires in a single hole must be of the same size and material. Distance between mounting holes is 1-3/4". NOTE: Consult local code for correct application of ground bar kit for service entrance equipment. Kit contains one ground bar and two #10-32 x 5/8" self-threading screws. UL Listed. For use with nonmetallic solvent weld fittings. Nonconductive, impact, corrosion and sunlight resistant.
Carlon E987G-CAR Rigid Conduit Body Schneider PK9GTACP Ground Bar Kit Square D PK12GTACP Ground Bar Kits
For easy access and pulling of wires through conduit run. For use with Schedule 40/80 non-metallic solvent weld fittings. Will not rust or corrode. UL Listed. Used in load centers, CSED devices and NQOD and NF panel boards. Each terminal accepts (1) #14 - #4 copper wire or (1) #12 - #4 aluminum wire, (2) #14 - #12 copper wire or (2) #12 - #10 aluminum wire. NOTE - Consult local code for correct application of ground bar kit for service entrance equipment. ANSI Certified and UL Listed. Used in load centers, CSED devices and NQOD and NF panel boards. Each terminal accepts (1) #14 - #4 copper wire or (1) #12 - #4 aluminum wire, (2) #14 - #12 copper wire or (2) #12 - #10 aluminum wire. NOTE - Consult local code for correct application of ground bar kit for service entrance equipment. ANSI Certified and UL Listed.
Carlon UAFAE Flexible Conduit Elbow Siemens EC2GB152 Ground Bar Kit With Terminal 2/0 Lug Siemens EC38598 Type RX Conduit Hub
Made of a highly durable plastic (PVC) compound making the product nonmetallic and safe to install. Elbow is non-corrosive, rustproof, and easily pliable. Good for those applications that requires change of direction. UL listed. For equipment grounding provision. #14 to 4 AWG, 60/75 degree Celsius, Cu/A1. For use on all Siemans and Murry single position meter sockets.
Halex 58807 Rigid Threaded Conduit Body with Cover and Gasket Halex 20442 Flexible Screw-In Connector Teddico/BWF 502V Thinwall Rigid Conduit Entrance Elbow
Copper-free die cast aluminum. Indoors or outdoors. Use to gain access to the interior of a raceway for wire pulling, splicing (with limitations as specified by the NEC), and maintenance. UL Approved. Tray boxed. Halex Screw-In Connector, Flexible, 3/4 in Nominal, 1.12 in Hex, Die Cast Zinc, 1.62 in Length, CSA Certified, UL Listed, For use to connect flexible metallic conduit to steel outlet box, load center or other metal enclosure, indoor use only Teddico/BWF Conduit Entrance Elbow, Thinwall, SLB, 1 in Hub, Rigid Conduit, Threaded Installation, Die Cast Aluminum, Gray, Powder Coated, Includes: Cover and Screw, CSA Certified, UL Listed, For connecting conduit sections, making bends in conduit runs as pull outlets, to provide openings for making splices and taps in conductors
Halex HX Rigid Conduit Connector Raco 8983-1 Ground Pigtail Steel City R Threaded Rod
Halex Conduit C