Home > ELECTRICAL > ROUGH ELECTRICAL > PANEL BOXES
Choose a sub category:
BREAKER BOXES MOBILE HOME LOAD CENTERS SPA PANEL BOXES
GENERATOR PANEL BOXES SAFETY SWITCHES DISCONNECT BOXES
METER BASES PANEL BOX ACCESSORIES UTILITY POWER OUTLETS
Sort By:
1
Cutler Hammer BRFPP Filler Plate GROUND BAR 7 HOLE CONSUMER PK GE THFILLER Rectangle Filler Plate
Plastic (snap-in) for type BR 1" space. May also be used with 400 amp and 600 amp load centers. For grounding copper or aluminum terminals in a GE load center. Offers 4 small holes for 14 - 8 AWG copper or 12 - 8 AWG aluminum terminals and 3 large holes for 14 - 4 AWG copper or 12 - 4 AWG aluminum terminals. UL Listed and ANSI Certified. 6.875" height x 2.875" width x 0.5" depth, .105 lb. Covers circuit breaker knock outs that have been removed in error.  Two 1" and two 1/2" plates.
LUG KIT NO6-2/0 NEUTRAL/GROUND Square D QOFPCP Filler Plate GROUND BAR 24 HOLE PM-GOLD PK
For use with wire range 6-2/0. Can be mounted on any neutral or ground position by simply removing the termination screw. UL Listed. 2.875" height x .75" width x  6.875" depth, .07 lb. Fills opening in covers if twistout is removed in error. QOFPCP are used only in QO load centers, filling the spaces where no circuit is attached. CHOMFPCP are for use only in Homeline load centers. UL Listed and ANSI Certified. Used for additional grounding as required by local code. Compatible with most load center enclosures. Fits solid or stranded 4 - 14 copper wire and 10 - 12 aluminum wire. Includes mounting screws. UL Listed and ANSI Certified. 11" height x 3.5" width x 0.5" depth, .304 lb.
Square D QO70AN Auxiliary Neutral Lug Kit Square D HOMFPCP Filler Plate Siemens ECQF3P Snap-On Filler Plate
Made for QO load centers. Field installed for number 12 - 2 Al or number 14 - 4 Cu wire. QO accessories can only be used with QO load centers. Fills opening in covers if twistout is removed in error. QOFPCP are used only in QO load centers, filling the spaces where no circuit is attached. CHOMFPCP are for use only in Homeline load centers. UL Listed and ANSI Certified. Siemens Filler Plate, Snap-On, Suitable For Use With: Load Centers and Meter Combinations, Plastic, ANSI Specified, CSA Certified, UL Listed, For used to fill open, unused positions in a panel
Schneider PK3GTA-1CP Ground Bar Kit Square D PK4GTACP Ground Bar Kits Square D HOM100AN Neutral Lug Kit
Used in load centers, CSED devices and NQOD and NF panel boards. Each terminal accepts (1) #14 - #4 copper wire or (1) #12 - #4 aluminum wire, (2) #14 - #12 copper wire or (2) #12 - #10 aluminum wire. NOTE - Consult local code for correct application of ground bar kit for service entrance equipment. ANSI Certified and UL Listed. Used in load centers, CSED devices and NQOD and NF panel boards. Each terminal accepts (1) #14 - #4 copper wire or (1) #12 - #4 aluminum wire, (2) #14 - #12 copper wire or (2) #12 - #10 aluminum wire. NOTE - Consult local code for correct application of ground bar kit for service entrance equipment. ANSI Certified and UL Listed. Breaker box neutral lug is designed for Homeline load centers. It works with number 1 - 1/0 copper and aluminum wire. UL Listed, ANSI Certified.
Siemens ECLX Ground Bar Kit Siemens ECLX Ground Bar Kit Siemens EC38595 Closure Plate
Siemens Ground Bar Kit, Series: ECLX, 7 Terminals, NO 14 - 6 Small Opening, NO 14 -1/0 Large Opening Conductor, ANSI Specified, CSA Certified, UL Listed, For Use With Murray branded Load Centers That are 12 1-Inch Spaces or Larger Siemens Ground Bar Kit, Series: ECLX, 11 Terminals, NO 14 - 6 Small Opening, NO 14 -1/0 Large Opening Conductor, 3-1/2 in Length, 5.1 in Width, 5.1 in Height, ANSI Specified, CSA Certified, UL Listed, For Use With Murray branded Load Centers That are 12 1-Inch Spaces or Larger Fits any meter socket application where a closure plate is needed.
Siemens ECLX Ground Bar Kit GE Electrical TFN60RCP AC Disconnect Switches Eaton DPU222RP Type ACD Non-Fusible Pullout Disconnect Switch
Siemens Ground Bar Kit, Series: ECLX, 19 Terminals, NO 14 - 6 Small Opening, NO 14 -1/0 Large Opening Conductor, ANSI Specified, CSA Certified, UL Listed, For Use With Murray branded Load Centers That are 12 1-Inch Spaces or Larger Steel enclosure. 2 pole, 3 wire, 240 volt AC, rated 10 HP. For central air conditioner. Removable closing cap not included. Equipment ground. 14 - 3 AWG lug wire range. 4-3/4" x 7-1/2" x 2". UL1429 enclosure pullout switch, UL Listed. Single phase, 2 pole, 2 wire, 240 volt AC, galvanized steel enclosure with molded case switch. Rated 3 HP at 120 volt, 10 HP at 240 volt. For bottom entry and exit only. Heavy duty, high strength enclosure with welded and riveted construction. Swing-up cover remains in place when in open position, and includes provision for padlocking. 10,000 AIR. When pullout is in off position, protective shield can be removed for access to fuses. No.GB4 ground bar and No.96-3258-4 pullout head replacement sold separately. #14-3 AWG wire range. 5-3/8" x 8-3/4" x 3-1/8". UL Listed file No.E5239.
Siemens Energy WN2060U AC Disconnect Switches SWITCH AC DISCONNECT 30A A    SWITCH AC DISCONNECT 60A A
Single phase, 2 pole, 2 wire, 240 volt, rated 10 HP, steel enclosure. All lugs positioned for bottom entry and exit wiring. Easy mounting for quick installation. Pullout head can be replaced in off position. 10,000 AIR. 12 - 3 AWG al, 14 - 3 kcmil cu lug wire range. 5-5/32" x 7-5/16" x 2-7/32". UL Listed. For use as service disconnect. Outdoor enclosed pullout switch. Type 3R, 240VAC, single phase. Removable door. cULus Listed. For use as service disconnect. Outdoor enclosed pullout switch. Type 3R, 240VAC, single phase. Removable door. cULus Listed.
Cutler-Hammer DPF221RP AC Disconnect Switches Square D S106 Replacement Screw Square D QO2L30SC Load Center
Air conditioning disconnect, pullout, fused, 2-pole, 120/240 volt AC. Wire size range of  #14-3 Cu or Al at 60 or 70 degrees C. Metallic color galvanized steel enclosure, 9" x 5.5" x 3". NEMA 3R, rainproof. UL Listed, CSA Approved. Fit many types of service entrance devices and load center covers. Use them to replace lost or damaged screws. Main lug load center, indoor, 30 amp, 2 spaces/2 circuits. Accommodates both overhead and underground feed applications. 1" maximum knockout on the top and bottom of the enclosure. Comes with a doorless surface mount cover and factory installed main lugs. UL Listed.
Cutler-Hammer AC222URNMP-A2 AC Disconnect Switches Homeline Square D HOM24L70S Load Center Eaton BR24L70SP Load Center
Single phase, 2 pole, 2 wire, 240 volt AC. Rated 3 HP at 120 volt, 10 HP at 240 volt. For top and bottom entry and exit, with provision for type H conduit hub. Heavy duty, high strength, rugged polymer enclosure with UV resistant features. Swing-up cover remains in place when in open position, protective shield can be removed for access to fuses. No.GB4 ground bar and No.360-011-24 pullout head replacement sold separately. #14-2 AWG wire range. 5" x 8-5/8" x 3-1/2". UL Listed file No. E5239. Main lug indoor load center, 70 amp, 2 spaces/4 circuits. Maximum SCCR of 10,000 and a maximum load of 240 volts. NEMA type 1 enclosure. Expandable loadcentre capacity with the use of tandem or quad breakers. CSA approved for vertical, horizontal or inverted mounting. Accepts aluminum or copper conductors. Approved to only accept Canadian HomeLine breakers. Steel enclosure. Single phase, 3 wire, insulated/bondable movable neutral, 2 (1") spaces, 4 poles, 120/240 volt. No.GBK5 or GBK520 ground bars and doors sold separately. Tin-plated aluminum bus bar. In accordance with NEC, suitable for use as service equipment when not more than 2 service disconnecting mains are provided or when not used as lighting and appliance panelboard. When bonded, unused neutral connections may be used for equipment ground protectors in service entrance application. #8 - #2 wire range. Electrostatic powder coat, baked urethane painted. Rotate 180 degrees for bottom feed. Style 5 box 4-1/2" x 9-7/16" x 3". UL Listed file E8741.
Eaton BR24L70FP Load Center GE Electrical TF60RCP AC Disconnect Switches Homeline Square D HOM24L70F Load Center
Single phase, 3 wire, insulated/bondable neutral, 2 (1") spaces, 4 poles, 120/240 volt AC. No. GBK5 or No. GBK520 ground bars and doors sold separately. Tin-plated aluminum bus bar. In accordance with NEC, suitable for use as service equipment when not more than 2 service disconnecting mains are provided or when not used as a lighting and appliance panelboard. Neutral is movable to other side. When bonded, unused neutral connections may be used for equipment ground protectors in service entrance application. #8 - #2 wire range. Electrostatic powder coat, baked urethane painted. Rotate 180 degrees for bottom feed. Style 5 box 4-1/2" x 9-7/16" x 3". UL Listed file E8741. Steel enclosure. 2 pole, 3 wire, 120/240 volt AC, rated 10 HP. Uses cartridge fuses. For central air conditioner. Designed to comply with code requirements for disconnecting means within sight of central air conditioners and heat pumps. Removable closing cap not included. Equipment ground. 14-3 AWG lug wire range. 6-1/2" x 9" x 3-1/4". UL869 service equipment, UL Listed. Main lug indoor load center, 70 amp, 2 spaces/4-circuits. NEMA type 1 enclosure with a flush mount cover. Overhead or underground feeds with 1-1/4" knockouts in both the top and bottom endwalls. Compatible with Homeline 1 pole and tandem breakers and a PK3GTA1 ground bar kit (not included). UL Listed.
Murray LC002GSU Load Center PowerMark Gold TL412C Standard Load Center Square D QO200TRCP Molded Non-Fusible Disconnect Switch
Murray Load Center, 240 VAC, 60 A, 1 Phases, 4 Wire Wiring, Main Lug Circuit Breaker, 2 Spaces, 8 Circuits, Surface Mounting, Powder Coated, Includes: Factory Installed Feed Through Lugs, UL Listed, For Indoor Applications Single-phase, three-wire, 120/240 volt AC. (4) 1" circuits or (8) 1/2" circuits. One-piece interior removes and reinstalls easily. Full-length neutrals are easier to wire, reducing installation time and cost. Minimum 100 percent neutral terminations. Sturdy copper bus and galvanized box increase durability and reliability. Combination slotted/Robertson screws speed wiring. All holes are rated for 14-4 wire. 100 per cent rated split neutral on each side. Load centers accept Q Line circuit breakers, including GE's exclusive 1/2" THQPs. 10,000 AIC. 40 - 225 amp single phase devices have removable closing caps. TL load center enclosures are galvanized steel. 7-1/4" x 9" x 3". UL Listed. For use with 75 degree Celsius wire. 2 pole, 2 wire, 240 volt AC, rated 10 HP, steel enclosure with molded case. With reliable, quick-make, quick-break operating mechanism. Suitable for use on systems with up to 10,000 RMS symmetrical amp available fault current at 240 volt AC maximum when protected by a fuse or circuit breaker rated 60 amp or less. Does not contain overcurrent protection. Ground bar bonded to back. 4-5/8" x 6-1/2" x 3-7/8". UL Listed.
Square D L111N Fusible Light Duty Safety Switch Square D L211N Safety Switches Cutler-Hammer DPF222RP AC Disconnect Switches
Single phase, 1 pole, 2 wire, solid neutral, 120/240 volt AC. Rated 2 HP at 120 volt AC, with metallic enclosure. Typical loads include workshop or hobby room, water heater, furnace, garage or well pump disconnect. 10,000 AIC (short circuit rating) with plug fuses. Padlock attachment for lock off. UL Listed, meets NEMA standard KS1. 5.00" x 7.63" x 4.00". Single phase, 2 pole, 3 wire, solid neutral, 120/240 volt AC. Rated 3 HP at 240 volt AC, with metallic enclosure. Typical uses include workshop or hobby room, water heater, furnace, garage or well pump disconnect. 10,000 AIC (short circuit rating) with plug fuses. Padlock attachment for lock off. 5.00" x 7.63" x 4.00". UL Listed, meets NEMA standard KS1. Air conditioning disconnect, pullout, fused, 2-pole, 120/240 volt AC. Wire size range of  #14-3 Cu or Al at 60 or 70 degrees C. Metallic color galvanized steel enclosure, 9" x 5.5" x 3". NEMA 3R, rainproof. UL Listed, CSA Approved.
Homeline Square D HOM612L100F Load Center Eaton BR48L125FP Load Center Square D QO24L70S Load Center
Main lug indoor load center, 100 amp, 6 space/12 circuit. 1-1/2" knockouts in the top and bottom end walls to allow for use with either overhead or underground fed electrical wiring. 22,000 short circuit current rating (SCCR) and can be fitted with a secondary surge arrestor (not included) for added protection. Single phase, 3 wire, solid neutral. UL Listed. Steel enclosure. Single phase, 3 wire, insulated/bondable neutral, 4 (1") spaces, 8 poles, 120/240 volt. No.GBK10 ground bars and doors sold separately. Tin-plated aluminum bus bar. In accordance with NEC, suitable for use as service equipment when not more than 2 service disconnecting mains are provided or when not more than 6 service disconnecting mains are provided and when not used as a lighting and appliance panelboard. Neutral is movable to other side. When bonded, unused neutral connections may be used for equipment ground protectors in service application. #14 - 1/0 AWG wire range. Electrostatic powder coat, baked urethane painted. Rotate 180 degrees for bottom feed. Style 7 box - 11" x 13" x 3-9/16". UL Listed file E8741. Main lug load center, intended for fixed applications. 70 amp, 2 spaces/4 circuits. Surface mount cover with door and a NEMA type 1 enclosure for indoor use. Single phase unit, features a copper bus for conductivity and is rated for up to 10,000 SCCR. ANSI Certified and UL Listed.
Eaton BR48L125SP Load Center Murray LC004NSU Load Center Homeline Square D HOM612L100S Load Center
Steel enclosure. Single phase, 3 wire, insulated/bondable neutral, 4 (1") spaces, 8 poles, 120/240 volt. No. GBK10 ground bars and doors sold separately. Tin-plated aluminum bus bar. In accordance with NEC, suitable for use as service equipment when not more than 2 service disconnecting mains are provided or when not more than 6 service disconnecting mains are provided and when not used as a lighting and appliance panelboard. Neutral is movable to other side. When bonded, unused neutral connections may be used for equipment ground protectors in service application. #14 - 1/0 AWG wire range. Electrostatic powder coat, baked urethane painted. Rotate 180 degrees for bottom feed. Style 7 box - 11" x 13" x 3-9/16". UL Listed file E8741. Single phase - 3 wire; 120/240 volt;  8 circuits maximum with 4 - 1" spaces. 14" length x 8-1/2" width x 3-1/4" depth. 10,000 AIC. UL listed. Main lug indoor load center, 100 amp,  6 space/12 circuit. NEMA type 1 enclosure.  Single phase, 3 wire, solid neutral. Expandable loadcentre capacity with the use of tandem or quad breakers. CSA approved for vertical, horizontal or inverted mounting. Accepts aluminum or copper conductors. Approved to only accept Canadian HomeLine breakers.
Cutler-Hammer DP221NGB Safety Switches Eaton BR24L70RP Load Center Cutler-Hammer ACD221RNMP AC Disconnect Switches
Steel enclosure. 2 pole, 3 wire, general duty safety switch, plug fuse type, (Type S, T, OR W) fusible with neutral NEMA 1. 120/240 volt rating. 1/2 HP at 120 volt, 1-1/2 HP at 240 volt. Does not have an interlock to prevent opening when switch is in the on position. UL Listed. Rainproof galvanized steel enclosure. Single phase, 3 wire, insulated/bondable movable neutral, 2 (1") spaces, 4 poles, 120/240 volt AC. With closure plates, hubs and No.GBK5 or GBK520 ground bar kits (necessary for sub-feeding) sold separately. Tin-plated aluminum bus bar. In accordance with NEC, suitable for use as service equipment when not more than 2 service disconnecting mains are provided or when not used as a lighting and appliance panelboard. When bonded, unused neutral connections may be used for equipment ground protectors in service entrance application. #8 - #2 wire range. Electrostatic powder coat, baked urethane painted. 4-1/2" x 9-7/16" x 3". UL Listed file E8741. Style 5R box. Single phase, 2 pole, 2 wire, 240 volt AC, non-metallic enclosure. Rated 1-1/2 HP at 120 volt, 3 HP at 240 volt with time delay fuses (uses class H cartridge fuses, not included). For top and bottom entry and exit, with provision for type H conduit hub. Heavy duty, high strength, rugged polymer enclosure with UV resistant features. 10,000 amp RMS symmetrical interrupting rating. Suitable for use as service entrance equipment with ground bar. No.GB4 ground bar and No.360-011-24 pullout head replacement sold separately. #14-2 AWG wire range. 5" x 8.63" x 3.5". UL Listed file No. E5239.
PowerMark Gold TLM612FCUD Standard Convertible Load Center Eaton BR612L125FDP Load Center Siemens E0204ML1060SU Load Center
Indoor flush or surface mount with door. Box is significantly smaller and lighter while maintaining optimum wire-bending space. Side mounted main  breaker allows top or bottom feed. Sturdy copper bus and galvanized box increase durability and reliability; tinplated for corrosion resistance. Minimum 100 per cent neutral terminations. All neutral holes rated for 14-4 wire. Extruded neutrals are easier to wire, reducing installation time and cost. Combination slotted/Robertson screws speed wiring. Accepts GE Q-Line branch circuit breakers, including GE's exclusive 1/2" THQPs. Interior removes and reinstalls easily. Main breaker not included. (6)  1" circuits or (12)  1/2"  circuits. 12-5/8" x 12-3/8" x 3-3/8". UL Listed. Steel enclosure. Single phase, 3 wire, insulated/bondable neutral, 6 (1") spaces, 12 poles, 120/240 volt. Furnished with door; No. GBK10 ground bar sold separately. Tin-plated aluminum bus bar. In accordance with NEC, suitable for use as service equipment when not more than 6 service disconnecting mains are provided and when not used as a lighting and appliance panelboard. Neutral is movable to other side. When bonded, unused neutral connections may be used for equipment ground protectors in service entrance application. Number 14 - number 1 AWG wire range. Electrostatic powder coat, baked urethane painted. Rotate 180 degrees for bottom feed. Style 7 box - 11" x 13" x 3-9/16". UL Listed file E8741. Single phase, 3 wire, solid neutral, 2 spaces and 4 circuits maximum 1-pole, 1 QP breaker maximum 2-pole, 120/240 volt AC. 10,000 AIR. One piece plated aluminum bus bar, heavier main bus for cooler operation, direct cable connection to bus bar. Main lugs and neutral on same plane, same drive tool. 100 percent circuit breaker twistouts. Positive load side circuit breaker hook rail. When used as service equipment, any unused neutral position may be used for equipment grounding. Simple upper pan adjustment after trim is installed for flush leveling. Rotate entire device 180 degrees for bottom feed. Gray enamel finish. UL Listed, complies fully with NEC and UL requirements for Class CTL. 5-1/8" x 9-7/8" x 2-5/8".
Siemens E0408ML1125SU Load Center Murray LC006NSU Load Center Square D QO612L100FCP Load Center
Code-gauge steel enclosure. Single phase, 3 wire, solid neutral, 4 spaces and 8 circuits maximum 1-pole, 2 QP breakers maximum 2-pole, 120/240 volt. 10,000 AIR. One piece plated aluminum bus bar. 100 percent circuit breaker twistouts. Positive load side circuit breaker hook rail. Suitable for use as service equipment when a main breaker (100 amp maximum) is back-fed in a branch position and used with main breaker retainer clip No.MBR1. When used as service equipment, any unused neutral position may be used for equipment grounding. Rotate entire device 180 degrees for bottom feed. Gray enamel finish. 6-5/8" x 12-5/8" x 3-1/2". UL Listed, complies fully with NEC and UL requirements for Class CTL. Murray Load Center, 240 VAC, 60 A, 1 Phases, Main Lug Circuit Breaker, 6 Spaces, 12 Circuits, Aluminum Buss Bar, Surface Mounting, Includes: Main Breaker, UL Listed, For Indoor Applications Main lug indoor load center, 100 amp, 6 space/12 circuit, intended for use in fixed applications. NEMA type 1 enclosure and a copper bus bar for conductivity. Single-phase, rated for up to 240 volts and has a 10,000 maximum SCCR. UL Listed.
Eaton BR816L125FP Load Center Homeline Square D HOM24L70RB Load Center Square D L221N Safety Switches
Steel enclosure. Single phase, 3 wire, insulated/bondable neutral, 8 (1") spaces, 16 poles, 120/240 volt. No.GBK10 ground bar and door sold separately. Tin-plated aluminum bus bar. In accordance with NEC, suitable for use as service equipment when a main breaker is used or when not more than 6 service disconnecting mains are provided and when not used as a lighting and appliance panelboard. Neutral is movable to other side. When bonded, unused neutral connections may be used for equipment ground protectors in service entrance application. #14 - #1 AWG wire range. Electrostatic powder coat, baked urethane painted. Rotate 180 degrees for bottom feed. Style 7 box - 11" x 13" x 3-9/16". UL Listed file E8741. Main lug outdoor load center, 70 amp, 2 space and 4 circuit. NEMA type-3R enclosure with a rainproof cover for outdoor use. Class 1170 unit is intended for use in fixed applications and can accommodate overhead or underground feed. Maximum SCCR of 10,000. ANSI Certified and UL Listed. Single phase, 2 pole, 3 wire (2 blades, fuseholders and 1 neutral), 120/240 volt AC. Rated 3 HP at 240 volt AC, with metallic enclosure. 10,000 AIC (short circuit rating) with class H cartridge fuses. NEMA type 1 enclosure. Terminal lug data: (1) #12 - 6 Al or #14 - 6 Cu. wire. Service ground bar kit PKGTA1 sold separately. Padlock attachment for lock off. UL Listed, meets NEMA standard KS1.
Square D D211NCP Safety Switches Square D QO612L100SCP Load Center Eaton DPB222RP Type ACD Molded Non-Automatic Breaker Disconnect Switch
Single phase, 2 pole, 3 wire, 2 blades and fuseholders, factory installed solid neutral, 120/240 volt AC. With metallic enclosure for indoor use. Designed to open or close an electrical circuit in general duty applications. Rated 1-1/2 HP. For residential or commercial applications. For PK3GTA-1 field installable service ground bar kit. With plug type fuse protection. Lugs suitable for aluminum or copper conductors. Spring reinforced plated copper fuse clips. ANSI Certified and UL Listed. Main lug indoor load center, 100 amp, 6 spaces/12 circuits. 1-1/2" maximum knockouts in the top and bottom end walls for overhead or underground feed. NEMA type 1 for indoor use. Steel enclosure. Single phase, solid neutral. UL Listed. Air conditioning disconnect, molded case switch looks like a circuit breaker but operates like an ordinary household light switch. 60 amp, 2-pole, 240 volt AC. Metallic, galvanized steel enclosure, NEMA 3R, rainproof. Packaged for retail sale. Wire size range Cu or Al at 60 or 70 degrees C: #14-3. UL Listed, CSA Approved.
Eaton BR816L125SDP Load Center Eaton BR612L125RP Load Center Eaton BR48L125RP Load Center
Steel enclosure. Single phase, 3 wire, insulated/bondable neutral, 8 (1") spaces, 16 poles, 120/240 volt. Furnished with door. Ground bar No.GBK10 sold separately. Tin-plated aluminum bus bar. In accordance with NEC, suitable for use as service equipment when a main breaker is used or when not more than 6 service disconnecting mains are provided and when not used as a lighting or appliance panelboard. Neutral is movable to other side. When bonded, unused neutral connections may be used for equipment ground protectors in service entrance application. #14-#1 wire range. Electrostatic powder coat, baked urethane painted. Rotate 180 degrees for bottom feed. Style 7 box - 11" x 13" x 3-9/16". UL Listed file E8741. Rainproof galvanized steel enclosure. Single phase, 3 wire, insulated/bondable movable neutral, 6 (1") spaces, 12 poles, 120/240 volt AC. With closure plates, hubs and No.GBK10 ground bar kits (necessary for sub-feeding) sold separately. Tin-plated aluminum bus bar. In accordance with NEC, suitable for use as service equipment when a main breaker is used or when not more than 6 service disconnecting mains are provided and when not used as a lighting and appliance panelboard. When bonded, unused neutral connections may be used for equipment ground protectors in service entrance application. #14-#1 wire range. Electrostatic powder coat, baked urethane painted. Style 7R box 11" x 13" x 3-9/16". UL Listed file E8741. Rainproof galvanized steel enclosure. Single phase, 3 wire, insulated/bondable movable neutral, 4 (1") spaces, 8 poles, 120/240  volt AC. With closure plates, hubs, and No.GBK10 ground bar kits (necessary for sub-feeding) sold separately. Tin-plated aluminum bus bar. In accordance with NEC, suitable for use as service equipment when not more than 2 service disconnecting mains are provided or when not more than 6 service disconnecting mains are provided and when not used as a lighting and appliance panelboard. When bonded, unused neutral connections may be used for equipment ground protectors in service entrance application. #14-1/0 wire range. Electrostatic powder coat, baked urethane painted. Style 7R box 11" x 13" x 3-9/16". UL Listed file E8741.
Eaton BR612L125SP Load Center Eaton BR24L125RP Enclosed Load Center Siemens GHN321NU Safety Switch
Steel enclosure. Single phase, 3 wire, insulated/bondable neutral, 6 (1") spaces, 12 poles, 120/240 volt. No.GBK10 ground bar and door sold separately. Tin-plated aluminum bus bar. In accordance with NEC, suitable for use as service equipment when a main breaker is used or when not more than 6 service disconnecting mains are provided and when not used as a lighting and appliance panelboard. Neutral is movable to other side. When bonded, unused neutral connections may be used for equipment ground protectors in service entrance appliance. #14 - #1 wire range. Electrostatic powder coat, baked urethane painted. Rotate 180 degrees for bottom feed. Style 7 box - 11" x 13" x 3-9/16". UL Listed file E8741. Rainproof galvanized steel enclosure. Single phase, 3 wire, insulated/bondable movable neutral, 2 (1") spaces, 4 poles, 120/240 volt AC. With closure plates, hubs and No.GBK5 or GBK520 ground bar kits (necessary for sub-feeding) sold separately. Tin-plated aluminum bus bar. In accordance with NEC, suitable for use as service equipment when not more than 2 service disconnecting mains are provided or when not used as a lighting and appliance panelboard. When bonded, unused neutral connections may be used for equipment ground protectors in service entrance application. #14-1/0 wire range. Electrostatic powder coat, baked urethane painted. Style 6R box 6-7/8" x 12" x 4-1/2". UL Listed file E8741. Siemens Safety Switch, 240 V, 30 A, 2 Poles, 3 Wires, Groundable Neutral Insulation, NEMA 1 Enclosure, UL Listed, For Indoor
PowerMark Gold TL240RCU Standard Load Center PowerMark Gold TL270RCUP Standard Load Center PowerMark Gold TLM812SCUDP Standard Convertible Load Center
Single-phase, three-wire, 120/240 volt AC. One-piece interior removes and reinstalls easily. Full-length neutrals are easier to wire, reducing installation time and cost. 100 percent neutral terminations. Sturdy copper bus and galvanized box increase durability and reliability. Combination slotted/Robertson screws speed wiring. All holes are rated for 14-4 wire. 100 per cent rated split neutral on each side. Load centers accept Q Line circuit breakers, including GE 1/2" THQP. (2) 1" or (4) 1/2"  spaces; 22,000 AIC. 7-1/4" x 10" x 3-31/4". One-piece interior removes and reinstalls easily. Full-length neutrals are easier to wire, reducing installation time and cost. Minimum 100 percent neutral terminations. Sturdy copper bus and galvanized box increase durability and reliability. Combination slotted/Robertson screws speed wiring. All holes are rated for 14-4 wire. 100-percent rated split neutral on each side. Load centers accept Q Line circuit breakers, including GE's exclusive 1/2"  THQPs. (2) 1" or (4 )1/2" spaces; 22,000 AIC. Single-phase, three-wire, 120/240 Volt AC. 7-1/4" x 10" x 3-3/4". Box is significantly smaller and lighter while maintaining optimum wire-bending space. Side mounted main breaker allows top or bottom feed. Sturdy copper bus and galvanized box increase durability and reliability; tinplated for corrosion resistance. Minimum 100 per cent neutral terminations. All neutral holes rated for 14-4 wire. Extruded neutrals are easier to wire, reducing installation time and cost. Combination slotted/Robertson screws speed wiring. Accepts GE Q-Line branch circuit breakers, including GE's exclusive 1/2" THQPs. Interior removes and reinstalls easily. Main breaker not included. (8) 1" circuits or (16) 1/2" circuits. 11-9/16" x 11-3/8" x 3-3/8". UL Listed.
Murray LW002GRU Load Center Siemens Energy LF211NU Safety Switches Cutler-Hammer DG221NGB Safety Switches
Single phase - 3 wire; 120/240 volt;  4 circuits maximum;  2 - 1" spaces ; 10,000 AIC. 9-1/4" x 6-5/8" x 3-3/8". UL Listed. Single phase, 2 pole, 3 wire, solid neutral, 120/240 volt. 10,000 AIC with plug fuses (not included). Metallic enclosure. Rated 1-1/2 HP standard/3 HP maximum. Compact size, quick-make, quick-break mechanism. Suitable for use as service entrance equipment. Cover interlock. Bottom cable entry and exit only, no hub provision supplied. Padlocking provision to lock cover closed or to lock in off position. Lugs suitable for copper or aluminum. Silver plated copper conductors. #14-6 AWG line, #14-8 load lug wire ranges. 5-1/2" x 8-1/4" x 5-13/16". UL Listed file No.E4776, NEMA type GD, meets federal specifications WS865C. Steel enclosure. 2 pole, 3 wire, 2 blades, 2 class H cartridge fuses (not included), solid neutral, 120/240 volt AC. Rated 1-1/2 to 3 HP single phase, 3 to 7-1/2 HP 3-phase at 240 volt only when dual element fuses are used. For residential and commercial applications. Suitable for light duty motor circuits and service entrance. For use on systems capable of delivering up to 10,000 RMS, symmetrical fault current. Bolt on hub provided. DS100GK ground kit sold separately. 6-1/6" x 7-1/2" x 6-3/4". UL Listed file No.E5239; meets UL98 for enclosed switches and NEMA standard KS1.
GE TL412R1P Standard Load Center Siemens EQ W0204ML1060U Load Center Murray LW004NRU Load Center
One-piece interior removes and reinstalls easily. Full-length neutrals are easier to wire, reducing installation time and cost. 100 percent neutral terminations. Sturdy copper bus and galvanized box increase durability and reliability. Combination slotted/Robertson screws speed wiring. All holes are rated for 14-4 wire. 100 per cent rated split neutral on each side. Load centers accept Q Line circuit breakers, including GE's exclusive 1/2" THQPs. (4) 1" or (8) 1/2"  spaces. Single-phase, three-wire, 120/240 Volt AC. 7-1/4" x 10" x 3-3/4". Single phase, 3 wire, solid neutral, 2 spaces and 4 circuits maximum 1-pole, 1 QP breaker maximum 2-pole, 120/240 volt AC. 10,000 AIR. With closure plates, HS style hubs sold separately, uses ECHA075 (694.3559) Hub. One piece plated aluminum bus bar. 100 percent circuit breaker twistouts. Will not accommodate 2-pole GFCI or circuit breaker with shunt trip. Positive load side circuit breaker hook rail. When used as service equipment, any unused neutral position may be used for equipment grounding. Rotate entire device 180 degrees for bottom feed. Gray enamel finish. CSA and UL Listed, complies fully with NEC and UL requirements for Class CTL. 5" x 8" x 4-1/4". Convertible to main breaker using double pole breaker. 2 full spaces. 4 space, 8 circuit, combination mount.
Square D HOM816L125PC Homeline Main Lug Load Center Siemens EQ W0408ML1125U Load Center LOAD CENTR 125A 8SP 16C INDOOR
Main lug indoor load center. Convertible to a main breaker with a QOM1 main breaker. Single-phase load center, NEMA type 1 enclosure, combination flush/surface indoor cover. Overhead or underground feed options. Plated aluminum bus bar. UL Listed. Code-gauge steel enclosure. Single phase, 3 wire, solid neutral, 4 spaces/8 circuits 1-pole, 2 QP breakers 2-pole, 120/240 volt AC. 10,000 AIR. With closure plates, HS-hubs sold separately. One piece plated aluminum bus bar. 100 percent circuit breaker twistouts. Positive load side circuit breaker hook rail. Suitable for use as service equipment when a main breaker (100 amp maximum) is back-fed in a branch position and used with main breaker retainer clip No.MBR1. When used as service equipment, any unused neutral position may be used for equipment grounding. Rotate entire device 180 degrees for bottom feed. Gray enamel finish. CSA and UL Listed, complies fully with NEC and UL requirements for Class CTL. 6" x 12-1/4" x 4-1/4". Value kit, indoor. Includes a sturdy highly-conductive tin-plated copper buss bar and a rust-resistant galvanized box. Indoor NEMA 1 enclosure with combination surface/flush front. Factory-installed main lug, full-length neutral bars, top or bottom feed and self-adjusting, dead-front cover. One-piece interior removes and re-installs easily. Single-phase, 3-wire, 120/240-volt and 22K AIC rating. All holes are rated for 14-4 wire and 100 percent rated split neutrals on each side. Accepts Q-Line THQL standard, GFCI and AFCI circuit breakers, including GE's exclusive 1/2" THQPs. UL Listed and ANSI Certified. 16" height x 14" width x 3.375" depth, 16.79 lb.
POWER OUTLET 50A 14-50R CON PK Homeline Square D HOM612L100RB Load Center Eaton CH2L70RP Load Center
Temporary RV power outlet is factory-assembled and factory-tested. Ready to use with no need to assemble individual parts. Single, heavy-gauge welded flange NEMA 3R rainproof enclosure protects against weather, vandalism and nuisance tripping. It is lockable and is engineered for maximum protection of receptacles, cords, plugs and breakers. All-in-one construction for factory assured terminations. Rolled edge door for cord protection. Manufactured from heavy G-90 zinc coated steel which resists corrosion and fading. Complies with National Electrical Code and OSHA requirements. 7" height x 5.5" width x 5.25" depth, 4.06 lb. Outdoor main lug load center, 100 amp, 6 space and 12 circuits. Can be wired for underground or overhead feeds with a 2-1/2" hub on the top and a 1-1/2" knockout on the bottom. NEMA type 3R enclosure resists rain for durable performance. ANSI Certified and UL Listed. Rainproof galvanized steel enclosure. Single phase, 3 wire, insulated/bondable neutral, 2 (3/4") spaces, 4 poles with CHNT breakers, 120/240 volt AC. With closure plates, hubs and ground bar No.GBK5 or No.GBK520 sold separately. Copper bus bar. In service entrance application, where neutral is bonded, unused neutral connections may be used for termination of equipment grounds. In accordance with NEC, suitable for use as service equipment when not more than 2 service disconnecting mains are provided or when not used as a lighting and appliance panelboard. #14 - 2 main lug wire range. Electrostatic powder coated. Style 5R box 4-1/2" x 9-1/2" x 3-1/8". UL Listed file E8741.
Murray LC008DSU Load Center Square D QO24L70RB Load Center PowerMark Gold TLM1212CCU Standard Convertible Load Center
Single phase type 1 with 8-1" spaces, 16 circuits. Use neutral lug kit DLK1 or DLK2 as required. Indoor closure with door. Main lug indoor load center, 70 amp, 2 spaces/4 circuits. Intended for overhead or underground feed. 1-1/4" maximum knockouts in the top and bottom end walls. NEMA 3R enclosure for outdoor use with a factory included cover. Copper bus for conductivity. UL Listed. Box is significantly smaller and lighter while maintaining optimum wire-bending space. Side mounted main  breaker allows top or bottom feed. Sturdy copper bus and galvanized box increase durability and reliability; tinplated for corrosion resistance. Minimum 100 per cent neutral terminations. All neutral holes rated for 14-4 wire. Extruded neutrals are easier to wire, reducing installation time and cost. Combination slotted/Robertson screws speed wiring. Accepts GE Q-Line branch circuit breakers, including GE's exclusive 1/2" THQPs. Interior removes and reinstalls easily. Main breaker not included. 14 spaces, 24 circuits. 14-1/8" x 16-1/8" x 3-3/8". UL Listed.
Murray LW006NRU Weatherproof Load Center Connecticut PS-13-HR Weatherproof Power Outlet Panel Connecticut PS-54-HR Weatherproof Power Outlet Panel
Murray Load Center, Weatherproof, 240 VAC, 125 A, 1 Phases, Main Lug Circuit Breaker, 6 Spaces, 12 Circuits, Copper Buss Bar, Surface Mounting, Carbon Steel, G-90 Hot Dipped Galvanized, Includes: Factory Installed Feed Through Lugs, UL Listed, For Indoor Applications Factory wired and completely assembled. Suitable for use with aluminum or copper wire. Cover design allows cord to be used when door is closed. 30 amp, 120 volt. 6-1/8" x 5-3/8" x 4-3/4". TT-30R NEMA receptacle. NEMA 3R weatherproof enclosure. Safe and easy to install. Factory wired and completely assembled. Suitable for use with aluminum or copper wire. Unique cover design allows cord to be used when door is closed. 50 amp, 120/240 volt. 6-18" x 5-3/8" x 4-3/4". 14-50R NEMA receptacle. NEMA 3R weatherproof enclosure.
LOAD CENTER 125A 8SPACE 16CIR POWER OUTLET 30AMP R32U CON PK Siemens E0816ML1125S Load Center
Single-phase, Three-wire, 120/240 volt AC. Convertible. Full-length neutrals are easier to wire, reducing installation time and cost. Removable closing cap. Minimum 100 percent neutral terminations. Sturdy copper bus and galvanized box increase durability and reliability. Combination slotted/Robertson screws speed wiring. All holes are rated for 14-4 wire. 100 per cent rated split neutral on each side. Load centers accept Q Line circuit breakers, including GE's exclusive 1/2"  THQPs. UL listed. 11-1/4" x 11-1/8" x 3-1/4". Temporary RV power outlet is factory-assembled and factory-tested. Ready to use with no need to assemble individual parts. Single, heavy-gauge welded flange NEMA 3R rainproof enclosure protects against weather, vandalism and nuisance tripping. It is lockable and is engineered for maximum protection of receptacles, cords, plugs and breakers. All-in-one construction for factory assured terminations. Rolled edge door for cord protection. Manufactured from heavy G-90 zinc coated steel which resists corrosion and fading. Complies with National Electrical Code and OSHA requirements. 5.5" height x 7.5" width x 9.75" depth, 6.525 lb. Code-gauge steel enclosure. Single phase, 3 wire, solid neutral, 8 spaces and 16 circuits maximum 1-pole, 4 QP breakers maximum 2-pole, 120/240 volt. 10,000 AIR. One piece plated aluminum bus bar. 100 percent circuit breaker twistouts. Positive load side circuit breaker hook rail. Suitable for use as service entrance equipment when a main breaker (125 amp maximum) is back-fed in branch position and used with main breaker retainer clip No.MBR1. When used as service equipment, any unused neutral position may be used for equipment grounding. Rotate entire device 180 degrees for bottom feed. Gray enamel finish. 12-3/8" x 14-3/4" x 3-7/8". UL Listed, complies fully with NEC and UL requirements for Class CTL.
Eaton BR816L125RP Load Center Square D QO612L100RBCP Load Center Square D HOM2040L125PC Homeline Main Lug Load Center
Rainproof galvanized steel enclosure. Single phase, 3 wire, insulated/bondable movable neutral, 8 (1") spaces, 16 poles, 120/240 volt AC. With closure plates, hubs and No.GBK10 ground bar kits (necessary for sub-feeding) sold separately. Tin-plated aluminum bus bar. In accordance with NEC, suitable for use as service equipment when a main breaker is used or when not more than 6 service disconnecting mains are provided and when not used as a lighting and appliance panelboard. When bonded, unused neutral connections may be used for equipment ground protectors in service entrance application. #14-#1 wire range. Electrostatic powder coat, baked urethane painted. Style 7R box 11" x 13" x 3-9/16". UL Listed file E8741. Outdoor main lug load center, 100 amp, 6 space 12 circuit. NEMA type 3R enclosure with a rainproof cover. Copper bus bar, accommodates standard QO or QO tandem circuit breakers. ANSI Certified and UL Listed. Main lug indoor load center. Convertible to a main breaker with a QOM1 main breaker. Single-phase load center, NEMA type 1 enclosure, combination flush/surface indoor cover. Overhead or underground feed options. Plated aluminum bus bar. UL Listed.
BRLC 125A 12/24CR AL BUS/WGB  Square D HOM816L125PRB Homeline Main Lug Load Center Siemens EQ W0816ML1125CU Load Center
BR style 1-inch loadcenter, main lug, ground bar, includes BREQS125 hold-down screw, 125A, single-phase, 24-pole, 24 circuits, 12 spaces, 120/240V, #6-2/0 AWG Cu/Al at 60 or 75 degreesC wire, NEMA 1 enclosure, b1 box size. Ground bar, includes BREQS125 hold-down screw. 10 kAIC interrupt rating. Aluminum bus, combination mounting. 3.88 in x 14.31 in x 16.75 in. Suitable for use as service equipment when no more than 6 main disconnecting means are provided or when not used as lighting and appliance panelboard. Has notch for brhdk125 hold-down kit. Main lug outdoor load center, 125 amp 8 space/16 circuit. Convertible to a main breaker. Single-phase load center. Overhead or underground feed options. Plated aluminum bus bar. UL Listed. Code-gauge steel enclosure. Single phase, 3 wire, solid neutral, 8 spaces/16 circuits 1-pole, 4 QP breakers 2-pole, 120/240 volt AC. 10,000 AIR. HS-hubs sold separately. One piece copper bus bar, 100 percent circuit breaker twistouts. Positive load side circuit breaker hook rail. Suitable for use as service equipment when a main breaker (125 amp maximum) is back-fed in a branch position, and used with main breaker retainer clip No. MBR1. When used as service equipment, any unused neutral position may be used for equipment grounding. Rotate entire device 180 degrees for bottom feed. Gray enamel finish. UL Listed, complies fully with NEC and UL requirements for Class CTL. 12-1/8" x 14-3/4" x 4-1/4".
Reliance PB30 Manual Outdoor Power Inlet Box GE Electrical TG3221R Spec-Setter Safety Switches Murray LNF222RU Non-Fusible Lever Safety Switch
Outdoor NEMA 3R power inlet box. May be installed outdoors up to 100 feet from a home's load center so your generator can be plugged in outside, away from open doors or windows. Designed to be hard-wired directly to Reliance transfer switches with building wire. Has four combination 1/2" and 3/4" knockouts (one on each side, bottom and back). 6" height x 4" width x 2.63" depth. UL listed. Designed for residential or light commercial applications where duty is not severe. Meets or exceeds NEMA Enclosed Switch Standard KS1-1983 for type GD, CSA certified; 60 degrees C/75 degrees C conductor rating. Two pole, 120/240 volt AC; 250 volt DC. Removable closing cap. Accepts Class H fuses (not included). Feature quick make, quick break mechanism. Suitable for use as service entrance equipment when installed in accordance with National Electrical Code. 6-7/8" x 9-7/8" x 3-5/16".UL Listed (Enclosed Switches No. 98). Single phase, 2 pole, 3 wire, 240 volt, 10,000 AIC maximum, rated 10 HP maximum. Compact size, quick-make, quick-break mechanism, galvanized steel enclosure. Bottom cable entry and exit only, no hub provision supplied. Padlocking provisions to lock cover or lock in off position. Lugs suitable for copper or aluminum. Silver plated copper conductors. GSGK60 equipment ground kit sold separately. Number 14-3 AWG line and load wire range. 5-9/16" x 8-1/4" x 3-1/8". UL Listed file No.E4776, NEMA Type GD, meets federal specifications WS865C.
Cutler-Hammer MBE24L125BTS Main Lug Breakers Reliance PB20 Outdoor Power Inlet Box Square D HOM2040M100PC Homeline Main Breaker Load Center
BR branch breaker type, DS style hub, surface mount, EUSERC, 10kAIC. Bottom and top feed, ring style, UG/OH service. UL Listed. Outdoor NEMA 3R power inlet box. May be installed outdoors up to 100 feet from a home's load center so your generator can be plugged in outside, away from open doors or windows. Designed to be hard-wired directly to Reliance transfer switches with building wire. Has four combination 1/2" and 3/4" knockouts (one on each side, bottom and back). 6" height x 4" width x 2.63" depth. UL listed. Built with a plated, aluminum bus bar. Main breaker installed. UL Listed.
Eaton BR1220B100 Load Center Square D QO124L125PGC QO Main Lug Load Center Square D UTRS213B Meter Sockets
Galvanized steel enclosure. Single phase, 3 wire, insulated/bondable split neutral, 12 (1") spaces, 20 poles, 120/240 volt.  Main breaker type BR at 10,000 AIR. Tin-plated aluminum bus bar. Twin neutral with non-removable cross bus. When bonded, unused neutral connections may be used for equipment ground protectors in service entrance application. #4 - 1/0 wire range. Electrostatic powder coat, baked urethane painted. Rotate 180 degrees for bottom feed; orientation of main breaker handle consistent with NEC 240-81 requirements because it operates horizontally. 14-5/16" x 18-3/4" x 3-7/8". UL Listed file E52977. Convertible to a main breaker with a QOM1 main breaker. Single-phase load center, NEMA type 1 enclosure,  combination flush/surface indoor cover. Overhead or underground feed options. Single phase, 3 wire, 4 jaw, 600 volt AC maximum. 10,000 rms symmetrical amp short circuit current rating. Hub provisions have an A-type size and its enclosure is made of aluminum. Supplied with bonded neutral. Requires bolt-on hub or closing plate (not included) for hub opening in top endwall. Bypass and jaw release sold separately. It can accommodate buildings supplied by overhead power lines or underground cables. UL Listed.
Speedfax S1224B1100 Convertible Load Center Square D HOM2040M100PCVP Homeline Main Breaker Load Center BRLC 125A 20/40CR AL BUS/WGB
Single phase, 3 wire, 22K A/C main breaker factory installed. Aluminum bus bar, tin plated. ANSI 61 gray powder coated. Suitable for use as service equipment when main breaker is installed or when not more than six main disconnecting means are provided. Convertible from main breaker to main lug. NEMA Type 1. 14.25" width x 3.88" depth. Built with a plated, aluminum bus bar. Main breaker installed. UL Listed. Type BR single-phase, main lug loadcenters. Three-wire 120/240 Vac. Insulated/bondable split neutral, 20 spaces, 24 circuits, indoor, c1 box size. Has notch for BREQS125 hold-down kit. Combination cover style. Ground bar GBK1220 installed.
PowerMark Gold TM2010CCU Standard Load Center Square D URTRS213B Meter Sockets Speedfax S2020B1100 Convertible Load Center
Single-phase, three-wire, 120/240 volt AC. (20) 1" spaces. One-piece interior removes and reinstalls easily. Full-length neutrals are easier to wire, reducing installation time and cost. Minimum 100 percent neutral terminations. Sturdy copper bus and galvanized box increase durability and reliability. Combination slotted/Robertson  screws speed wiring. All holes are rated for 14-4 wire. 100 per cent rated split neutral on each side. Load centers accept Q Line circuit breakers, including GE's exclusive 1/2"  THQPs. 100-225 amp devices have removable closing cap. 22,000 AIC. 14" x 23" x 3-3/4". UL Listed. Single phase, 3 wire, 4 jaw, 600 volt AC maximum. Without bypass or jaw release. Steel enclosure material. Unit supplied with bonded neutral. 10,000 RMS symmetrical ampere short circuit current rating. Type-A hub provisions and the bottom end-wall has a 2-1/2" maximum knockout. Metering is utility specific. Always check with local utility company before installing. UL listed. Single phase, 3 wire, 22K A/C main breaker factory installed. Aluminum bus bar, tin plated. ANSI 61 gray powder coated. Suitable for use as service equipment when main breaker is installed or when not more than six main disconnecting means are provided. Convertible from main breaker to main lug. NEMA Type 1. 14.25" width x 3.88" depth.
LOAD CENTR 125A 12SPACE 24CIR Cutler-Hammer DG321NRB Safety Switches Square D HOM1224M100PC Homeline Main Breaker Load Center
Value kit, indoor. Includes a sturdy highly-conductive tin-plated copper buss bar and a rust-resistant galvanized box. Indoor NEMA 1 enclosure with combination surface/flush front. Factory-installed main lug, full-length neutral bars, top or bottom feed and self-adjusting, dead-front cover. One-piece interior removes and re-installs easily. Single-phase, 3-wire, 120/240-volt and 22K AIC rating. All holes are rated for 14-4 wire and 100 percent rated split neutrals on each side. Accepts Q-Line THQL standard, GFCI and AFCI circuit breakers, including GE's exclusive 1/2" THQPs. UL Listed and ANSI Certified. 16" height x 14" width x 3.375" depth, 16.79 lb. Steel enclosure. 3 pole, 4 wire, 3 blades, 3 class H cartridge fuses (not included), solid neutral, 120/240 volt AC, Rated 1-1/2 to 3 HP single phase, to 7-1/2 HP 3-phase at 240 volt only when dual element fuses are used. For residential or light commercial applications. Suitable for light duty motor circuits and service entrance. For use on systems capable of delivering up to 10,000 RMS, symmetrical fault current. Ample wire bending space for easier installation. DS100GK ground lug kit sold separately. 6-3/4" x 9-1/8" x 6-3/4". UL Listed file No.E5239; meets UL98 for enclosed switches and NEMA standard KS1. Built with a plated, aluminum bus bar. Main breaker installed. UL Listed.
BRLC 100A MN 20/40 CR         Speedfax S2040B1200 Convertible Load Center LOAD CENTER 100A 1P3W 120/240V
BR style 1-inch loadcenter, main circuit breaker, no feed-thru lugs, 100A, single-phase, 40-pole, 40 circuits, 20 spaces, 120/240V, #4-1/0 AWG Cu/Al at 60 or 75 degreesC wire, Three-wire, NEMA 1 enclosure, d1 box size. Interrupt Rating 25 kAIC. Aluminum bus. Combination mounting. 5.19 in x 14.31 in x 25 in. UL 50, UL 67. Cover included. Single phase, 3 wire, 22K A/C main breaker factory installed. Aluminum bus bar, tin plated. ANSI 61 gray powder coated. Suitable for use as service equipment when main breaker is installed or when not more than six main disconnecting means are provided. Convertible from main breaker to main lug. NEMA Type 1. 14.25" width x 3.88" depth. Value kit, indoor. Includes a sturdy highly-conductive tin-plated copper buss bar and a rust-resistant galvanized box. Indoor NEMA 1 enclosure with combination surface/flush front. Factory-installed main lug, full-length neutral bars, top or bottom feed and self-adjusting, dead-front cover. One-piece interior removes and re-installs easily. Single-phase, 3-wire, 120/240-volt and 22K AIC rating. All holes are rated for 14-4 wire and 100 percent rated split neutrals on each side. Accepts Q-Line THQL standard, GFCI and AFCI circuit breakers, including GE's exclusive 1/2" THQPs. UL Listed and ANSI Certified. 16" height x 14" width x 3.375" depth, 16.79 lb.
Murray LW102NLU Load Center Square D QO112M100C Load Center BRLC 200A 20/40 CR ALBUS/WGB
Single phase, 2 spaces/4 circuits, 120/240 volt. 10,000 AIR. Factory installed main breaker. Additional spaces allow connection of external circuits such as yard lights. One 1-1/4" HS125 hub included. Normally used as a means of disconnecting power to a mobile home panel, but also used as a disconnect for houses. Aluminum bus bar insulates and secures interior. Gray enamel finish. Pole mountable. 12-1/2" height x 6" width x 4-1/4" depth. UL Listed for use as service entrance equipment. Welded sheet steel. Single phase, 3 wire, split neutral, 12 spaces/12 circuit, 120/240 volt. 22,000 AIR factory installed main breaker. Comes with a ground bar and a combination cover for added protection. Shielded copper bus bar. 2-1/2" knockouts located on the top and bottom. Accepts QO circuit breakers and is compatible with overhead and underground service feeds. UL Listed. BR style 1-inch loadcenter, main lug, ground bar, includes BREQS125 hold-down screw, 200A, single-phase, 40-pole, 40 circuits, 20 spaces, 120/240V, #1-300 kcmil Cu/Al at 60 degreesC or 75 degreesC wire, three-wire NEMA 1 enclosure, c2 box size. Cover included. 3.88 in x 14.31 in x 23 in. Has notch for brhdk125 hold-down kit.
Eaton BR1224L200R Load Center Square D HOM2040M200PC Homeline Main Breaker Load Center LOADCENTER 100A 20/40 VP
Rainproof galvanized steel enclosure. Single phase, 3 wire, insulated/bondable split neutral, 12 (1") spaces 24 poles, 120/240 volt AC. Has notch for No.BRHDK125 hold down kit. With closure plates, hubs and ground bar kits (necessary for sub-feeding) sold separately. Tin-plated aluminum bus bar. In accordance with NEC, suitable for use as service equipment when not more than 6 main disconnecting means are provided and when not used as lighting and appliance panelboard. Twin neutral with non-removable cross bus. When bonded, unused neutral connections may be used for equipment ground protectors in service entrance application. #1 - 300 kcmil wire. Electrostatic powder coat, baked urethane painted. B2R box 14-5/16" x 18-3/4" x 5-3/16". UL Listed file E52977. Built with a plated, aluminum bus bar. Main breaker installed. UL Listed. BR style 1-inch loadcenter, main circuit breaker, value pack, 100A, single-phase, 40-pole, 40 circuits, 20 spaces, 120/240V. Wire size #4-1/0 AWG Cu/Al at 60 or 75 degreesC, NEMA 1 enclosure, d1 box size. Aluminum bus, combination mounting. 3.88 in x 14.31 in x 18.75 in. Includes 6-br120. Cover included.
Reliance Controls TF151W Generator Transfer Switches Cutler-Hammer MBE1224B100BTS Meter Socket Load Centers POWER PANEL RV 70A 50/20A GFCI
Economical, allows powering an otherwise hard-wired furnace blower motor with a portable generator for heat and to prevent frozen pipes during a power outage. Uses standard 15 amp extension cord. Full-color packaging. UL1008 Listed. Standard meter center, all-in-one, 1-inch BR branch breaker type, EUSERC, 25 KAIC, 12/24 distribution, BR2100 main breaker included. Bottom and top feed, ring style, UG/UG service. Rainproof enclosure. 5-3/8" depth x 14-7/16" width x 23-7/8" height. Unmetered RV outlet box. Rugged 16-gauge zinc coated G-90 steel, with electro-deposition finish resists corrosion and fading. NEMA 3R rainproof enclosure protects against weather, vandalism and nuisance tripping. Factory wired, assembled and tested. All-in-1 construction for factory assured terminations. Suitable for use as service entrance equipment when installed in accordance with the National Electric Code. Accepts copper or aluminum wire for added installation flexibility. Rolled edge door for cord protection. Dead front construction prevents accidental contact with live parts. Stay open position on door for convenience. Padlock provision. UL/CUL Listed (Power Outlets).
Eaton MBE1224B100BTF All-in-One Ring Meter Breaker/Center Eaton BR1020B100RF Load Center Siemens Energy MC1020B1100S Meter Socket Load Centers
Standard meter center, all-in-one, 1-inch BR branch breaker type, EUSERC, 25 KAIC, 12/24 distribution, BR2100 main breaker included. Bottom and top feed, ring style, UG/UG service. Rainproof enclosure. 5-3/8" depth x 14-7/16" width x 23-7/8" height. Rainproof galvanized steel enclosure. Single phase, 3 wire, insulated/bondable split neutral, 10 (1") spaces, 20 poles, 120/240 volt AC. Main breaker type BR at 10,000 AIC. Includes feed thru lugs for both phase and neutral conductors. With hub closure plates, hubs and ground bar kit (necessary for sub-feeding) sold separately. Tin plated aluminum bus bar. Twin neutral with non-removable cross bus connecting them. When bonded, unused neutral connections may be used for equipment ground protectors in service entrance application. #4 - 1/0 wire range. Electrostatic powder coat, baked urethane painted. Rotate 180 degrees for bottom feed; orientation of main breaker handle consistent with NEC 240-81 requirements because it operates horizontally. 14-5/16" x 18-3/4" x 5-3/16". UL Listed file E52977. Combination meter socket. Surface mount, overhead service entrance only. 100 amp maximum, 100 amp main breaker installed. Single phase, 3 wire. 10 spaces, 20 circuits, 22,000 AIC rating. Nema type 3R outdoor enclosure. Uses RX style hub, not included.
Speedfax S3040B1200 Convertible Load Center Square D HOM3060M200PC Homeline Main Breaker Load Center Square D HOM3060M200PCVP Homeline Main Breaker Load Center
Single phase, 3 wire, 22K A/C main breaker factory installed. Aluminum bus bar, tin plated. ANSI 61 gray powder coated. Suitable for use as service equipment when main breaker is installed or when not more than six main disconnecting means are provided. Convertible from main breaker to main lug. NEMA Type 1. 14.25" width x 3.88" depth. Built with a plated, aluminum bus bar. Main breaker installed. UL Listed. Built with a plated, aluminum bus bar. Main breaker installed. UL Listed.
BR SPA 50A ST   GFI           Midwest UG412RMW250 Spa Panel PowerMark Gold TM2020CCUP Load Center
Spa panel, wire size - number 8-2 Cu/Al. 60 or 75 degreesC. NEMA 3R enclosure. Box size - 5R. Includes factory installed breaker, ground-fault self test. 10.2 In X 4.9 In X 4.3 In, 4.45 lb. UL Listed. Single phase, 2 or 4 breaker spaces. 50 amp GFI protection rating. Moisture resistant use around water heaters, swimming pools, spas, hot tubs, garden tubs, pools, etc. Includes 2 pole 50 amp ground fault breaker. Single-phase, three-wire, 120/240 volt AC. (20) 1", (40) 1/2" spaces. One-piece interior removes and reinstalls easily. Full-length neutrals are easier to wire, reducing installation time and cost. 100 percent neutral terminations. Sturdy copper bus and galvanized box increase durability and reliability. Combination slotted/Robertson screws speed wiring. All holes are rated for 14-4 wire. 100 per cent rated split neutral on each side. Load centers accept Q Line circuit breakers, including GE's exclusive 1/2" THQPs. 100-225 amp devices have removable closing cap. 22,000 AIC. 14" x 28-7/16" x 3-3/4". UL Listed.
Eaton BR2040B200 Load Center Siemens Energy MC1224B1100EFC Meter Socket Load Centers Square D HOM816M200PFTRB Hom Main Breaker Load Center
Steel enclosure. Single phase, 3 wire, insulated/bondable split neutral, 20 (1") spaces, 40 circuits, 120/240 volt. Main breaker type BWH at 25,000 AIC. Tin-plated aluminum bus bar. Twin neutral with non-removable cross bus connecting them. When bonded, unused neutral connections may be used for equipment ground protectors in service entrance application. Number 2 - 300 kcmil wire range. Electrostatic powder coat, baked urethane painted. Orientation of main breaker handle consistent with NEC 240-81 requirements because it operates horizontally. UL Listed file E52977. 14-5/16" width x 29-1/8" height x 3-7/8" depth. Combination meter socket. flush mount, 100 amp maximum, 100 amp main breaker installed. Single phase, 3 wire. 22,000 AIC rating. Aluminum bus bars. Nema type 3R outdoor enclosure. Complies with EUSERC Dwg. No. 301. Single phase, 3 wire, insulated/bonded split neutral. 200 amp, 8 spaces/16 circuits maximum. 120/240 volt AC. 10,000 AIR. For mobile homes and farm applications. Overhead or underground feeds and offers feed-thru lugs. Plated aluminum bus bar. Has a 22,000 maximum short circuit current rating. Provided equipment: circuit breaker [space(1) 2P 200 amp 120/240 volt AC main supply ready assembled and grounding bar [space(1) ready assembled. UL Listed.
PowerMark Gold TM820RCUFLP Load Center GE Electrical TSM420CSCUP Powermark Gold Meter Socket Load Centers Eaton BR816B200RF Load Center
Factory Installed main breaker. Single phase, three wire, 120/240 volt AC. (8) 1" or (16) 1/2" spaces; 22,000 AIC. One piece interior removes and reinstalls easily. Full length neutrals are easier to wire, reducing installation time and cost. Minimum 100 per cent neutral terminations. Sturdy copper bus and galvanized box increase durability and reliability. Combination slotted/Robertson screws speed wiring. All holes are rated for 14-4 wire. 100 per cent rated split neutral on each side. Load centers accept Q Line circuit breakers, including GE 1/2" THQP. 100-225 amp devices have removable closing cap. 12-1/2" x 28-11/16" x 4-5/8". UL Listed. Feed through lugs. Single phase, 3 wire, bonded neutral, 8 total 1-pole spaces, 120/240 volt AC. 10,000 AIC. Four 1-pole or two 2-pole 1" THQL spaces, eight 1-pole or three 2-pole 1/2" THQP spaces. Main breaker factory installed. 6-350 main wire size. Padlock provisions on door. Hinged door is removable for safety and convenience. 14" x 28" x 4-1/2" UL Listed. Meets EUSERC requirements. Rainproof galvanized steel enclosure. Single phase, 3 wire, insulated/bondable neutral, 8 (1") spaces, 16 circuits, 120/240 volt AC. Main breaker type BWH at 25,000 AIC. Includes feed thru lugs for both phase and neutral conductors. With hub closure plates, hubs and ground bar kit (necessary for sub-feeding) sold separately. Tin plated aluminum bus bar. Neutral is movable to other side. When bonded, unused neutral connections may be used for equipment ground protectors in service entrance application. #2 - 300 kcmil wire range. Electrostatic powder coat, baked urethane painted. Rotate 180 degrees for bottom feed; orientation of main breaker handle consistent with NEC 240-81 requirements because it operates horizontally. 14-5/16" x 25" x 5-3/16". UL Listed file E8741.
Square D HOM4080M200PC Homeline Main Breaker Load Center ENCLOSURE MAIN BREAKER 2P 200A LOAD CNTR 200A 20SP 32C INDOOR
Built with a plated, aluminum bus bar. Main breaker installed. UL Listed. Galvanized steel outdoor enclosure. CCVH factory installed (25 kAIC) Circuit breaker. 2/0?300 kcmil wire size range. Approved for use as a service entrance. 2 pole 200 amp. Value kit, indoor. Includes a sturdy highly-conductive tin-plated copper buss bar and a rust-resistant galvanized box. Indoor NEMA 1 enclosure with combination surface/flush front. Factory-installed main lug, full-length neutral bars, top or bottom feed and self-adjusting, dead-front cover. One-piece interior removes and re-installs easily. Single-phase, 3-wire, 120/240-volt and 22K AIC rating. All holes are rated for 14-4 wire and 100 percent rated split neutrals on each side. Accepts Q-Line THQL standard, GFCI and AFCI circuit breakers, including GE's exclusive 1/2" THQPs. UL Listed and ANSI Certified. 16" height x 14" width x 3.375" depth, 16.79 lb.
BRLC 200A 40/40 CR ALBUS/WGB  Speedfax MC0408B1200RT Load Center Speedfax MC0408B1200T Load Center
BR style 1-inch loadcenter, main lug, ground bar, 200A, single-phase, 40-pole, 40 circuits, 40 spaces, 120/240V, #1-300 kcmil Cu/Al at 60 or 75 degreesC, NEMA 1 enclosure, G1 box size. Aluminum bus, Three-wire. Cover included. 3.88 in x 14.31 in x 34.13 in, 34 lb. Has notch for brhdk125 hold-down kit. UL 67, UL 50. Combination meter socket. 200 amp main breaker installed, Single phase, 3 wire, insta-wire neutrals. 4 spaces, 8 circuits. 120/240 volt.  22,000 AIC rating. 4 jaws. Tin plated copper bus bars. Nema type 3R outdoor enclosure. Overhead or underground feed. Feed thru lugs provided. Key hole shaped mounting holes for easy hanging. Deadfront pull ring and side hinge door. Captive dead front screw. RX style hub sold separately. UL Listed. Combination meter socket. 200 amp main breaker installed, Single phase, 3 wire, insta-wire neutrals. 4 spaces, 8 circuits. 120/240 volt.  22,000 AIC rating. 4 jaws. Tin plated copper bus bars. Nema type 3R outdoor enclosure. Overhead or underground feed. Feed thru lugs provided. Key hole shaped mounting holes for easy hanging. Deadfront pull ring and side hinge door. Captive dead front screw. RX style hub sold separately. UL Listed.
Eaton BR3040B200V Load Center Eaton BR3040B200 Load Center Eaton MBT48B200BTS All-in-One Ringless Meter Breaker/Center
Galvanized steel enclosure. Single phase, 3 wire, insulated/bondable split neutral, 30 (1") spaces, 40 poles, 120/240 volt. Main breaker type BW at 25,000 AIC. Ground bar kit (necessary for sub-feeding) sold separately. Tin plated aluminum bus bar. Twin neutral with non removable cross bus. When bonded, unused neutral connections may be used for equipment ground protectors in service entrance application. #2 - 300 kcmil wire range. Electrostatic powder coat, baked urethane painted. Rotates 180 degrees for bottom feed; orientation of main breaker handle consistent with NEC 240-81 requirements because it operates horizontally. G1 box - 14-5/16" width x 34-1/8" height x 3-7/8" depth. UL Listed file E52977. Galvanized steel enclosure. Single phase, 3 wire, insulated/bondable split neutral, 30 (1") spaces, 40 poles, 120/240 volt. Main breaker type BW at 25,000 AIC. Ground bar kit (necessary for sub-feeding) sold separately. Tin plated aluminum bus bar. Twin neutral with non removable cross bus. When bonded, unused neutral connections may be used for equipment ground protectors in service entrance application. #2 - 300 kcmil wire range. Electrostatic powder coat, baked urethane painted. Rotates 180 degrees for bottom feed; orientation of main breaker handle consistent with NEC 240-81 requirements because it operates horizontally. G1 box - 14-5/16" width x 34-1/8" height x 3-7/8" depth. UL Listed file E52977. All-In-One combination service entrance (includes distribution section), BR branch breaker type - Non-EUSERC, 25 kAIC, 4/8 distribution, 4 jaws, main breaker included. Bottom and top feed breaker, ringless security, OH/UG service. 12.50" height x 14.44" width x 4.00" depth. Wire size range Cu/Al  60 degrees C. Uses a DS-series hub, sold separately.
Eaton MBT48B125BTS All-in-One Ringless Meter Breaker/Center LOAD CNTR 200A 20SP 32C OUTDOR Speedfax MC0816B1200RCT Load Center
All-In-One combination service entrance (includes distribution section), BR branch breaker type - Non-EUSERC, 25 kAIC, 4/8 distribution, 4 jaws, main breaker included. Bottom and top feed breaker, ringless security, OH/UG service. 12.50" height x 14.44" width x 4.00" depth. Wire size range Cu/Al  60 degrees C. Uses a DS-series hub, sold separately. Value kit includes outdoor 200-amp main breaker load center, 3 20-amp single-pole and 1 30-amp double-pole THQP 1/2" circuit breakers. Includes a sturdy highly-conductive tin-plated copper buss bar and a rust-resistant galvanized box. Outdoor NEMA 3R enclosure. Factory-installed main breaker, full-length neutral bars, top or bottom feed and self-adjusting, dead-front cover. One-piece interior removes and re-installs easily. Single-phase, 3-wire, 120/240-volt and 22K AIC rating. All holes are rated for 14-4 wire and 100 percent rated split neutrals on each side. Accepts Q-Line THQL standard, GFCI and AFCI circuit breakers, including GE's exclusive 1/2-in THQPs. UL Listed and ANSI Certified. 34.19" height x 14.69" width x 5.23" depth, 43 lb. Combination meter socket. 200 amp main breaker installed, Single phase, 3 wire, insta-wire neutrals. 8 spaces, 16 circuits. 120/240 volt.  22,000 AIC rating. 4 jaws. Tin plated copper bus bars. Nema type 3R outdoor enclosure. Overhead or underground feed. Feed thru lugs provided. Key hole shaped mounting holes for easy hanging. Deadfront pull ring and side hinge door. Captive dead front screw. RX style hub sold separately. UL Listed.
LOADCENTER 40SPS 200A VP      PowerMark Gold TM4020CCU Standard Load Center Homeline Square D SC2040M200C All-in-One Combination Load Center
BR style 1-inch loadcenter, main circuit breaker, current design, 200A, single-phase, 50-pole, 50 circuits, 40 spaces, 120/240V, #1-300 kcmil Cu/Al at 60 or 75 degreesC, NEMA 1 enclosure, 6r box size. Metallic, interrupt rating - 10 kAIC. Aluminum bus, three-wire. Includes 3-br120, 1-br230, cover included. 4.5 In x 6.5 in x 11.75 in, 42 lb. Single-phase, three-wire, 120/240 volt AC. (40) 1" spaces; 22,000 AIC. One piece interior removes and reinstalls easily. Full-length neutrals are easier to wire, reducing installation time and cost. 100 percent neutral terminations. Sturdy copper bus and galvanized box increase durability and reliability. Combination slotted/Robertson screws speed wiring. All holes are rated for 14-4 wire. 100 per cent rated split neutral on each side. Load centers accept Q Line circuit breakers, including GE's exclusive 1/2" THQPs. Removable closing cap. 14" x 39-3/16" x 3-3/4". UL Listed. Combination service entrance device (CSED), referred to as an all in one that includes the utility meter socket, main service disconnect, and integral load center in a single enclosure.  Ring type and overhead or underground feed, rated 200A and surface mount. Single phase, 3 wire. 10,000 short circuit rating. 20 space, 40 circuit. Meets EUSERC standards. Service disconnects are supplied factory installed. Supplied with 100 percent branch neutrals. Meets Federal Specification W-P-115c as Type 1, Class 2. Convertible to semiflush with SC200F flange kit (sold separately). Suitable only for use as service equipment. UL Listed.
BRLC 200A MN 40/50 CIR        POWER PANEL RV 100A 50/30/20A Square D QO130M200PC QO Main Breaker Load Center
Main circuit breaker loadcenter; 200 amp, 120/240 volt AC, 50 circuit, 40 spaces, 1-phase. Tin plated aluminum bus. Twin neutral design. Feed-through lug. UL listed. Unmetered RV outlet box. Rugged 16-gauge zinc coated G-90 steel, with electro-deposition finish resists corrosion and fading. NEMA 3R rainproof enclosure protects against weather, vandalism and nuisance tripping. Factory wired, assembled and tested. All-in-1 construction for factory assured terminations. Suitable for use as service entrance equipment when installed in accordance with the National Electric Code. Accepts copper or aluminum wire for added installation flexibility. Rolled edge door for cord protection. Dead front construction prevents accidental contact with live parts. Stay open position on door for convenience. Padlock provision. UL/CUL Listed (Power Outlets). Convertible Indoor Plug-on Neutral load center for plug-on neutral breakers. Built with a shielded copper bus bar. UL listed.
Eaton BR2040B200R Load Center Eaton BR3040B200V2 Load Center Eaton MB816B200BTS Ringless Load Center
Rainproof galvanized steel enclosure. Single phase, 3 wire, insulated/bondable split neutral, 20 (1") spaces, 40 poles, 120/240 volt AC. Main breaker type BW at 25,000 AIC. Furnished with hub closure plates, hubs and ground bar kit (necessary for sub-feeding) sold separately. Tin plated aluminum bus bar. Twin neutral with non-removable cross bus connecting them. When bonded, unused neutral connections may be used for equipment ground protectors in service entrance application. #2 - 300 kcmil wire range. Electrostatic powder coat, baked urethane painted. Rotate 180 degrees for bottom feed; orientation of main breaker handle consistent with NEC 240-81 requirements because it operates horizontally. 14-5/16" x 29-1/8" x 5-3/16". UL Listed file E52977. Galvanized steel enclosure. Single phase, 3 wire, insulated/bondable split neutral, 30 (1") spaces, 40 poles, 120/240 volt. Main breaker type BW at 25,000 AIC. Ground bar kit (necessary for sub-feeding) sold separately. Tin plated aluminum bus bar. Twin neutral with non removable cross bus. When bonded, unused neutral connections may be used for equipment ground protectors in service entrance application. #2 - 300 kcmil wire range. Electrostatic powder coat, baked urethane painted. Rotates 180 degrees for bottom feed; orientation of main breaker handle consistent with NEC 240-81 requirements because it operates horizontally. G1 box - 14-5/16" width x 34-1/8" height x 3-7/8" depth. UL Listed file E52977. All-In-One, 1-inch BR type - Non-EUSERC, 25 kAIC, 8/16 distribution, 4 jaws, main breaker Included.  BW2200, main breaker bottom and top feed, ringless security, OH/UG service.
Eaton CH42B200KP Load Center POWER PEDESTAL BURIAL RV 100A Square D QO142M200PC QO Main Breaker Load Center
Sheet steel enclosure. Single phase, 3 wire, factory bonded split neutral, 42 (3/4") spaces, 42 poles, 120/240 volt. Main breaker type CSR at 35,000 AIC when used with CH or CHP branch breakers. Solid copper bus bar. Twin neutral with cross bus. Unused neutral connections may be used for termination of equipment grounds. Listed for use as service equipment with twin neutral doubling as neutral/ground; remove bonding strap for separate neutral/ground bars for sub-feed applications. Includes combination surface/flush cover. #2 - 300 kcmil wire range. Electrostatic powder coat, baked urethane painted. Rotate enclosure and trim 180 degrees for bottom feed. 14-5/16" x 37" x 3-7/8". UL Listed file E8741. Unmetered earth burial pedestal with 50 amp, 30 amp and 20 amp GFCI circuit protected receptacles. 16-gauge zinc coated G-90 steel, with electro-deposition finish resists corrosion and fading. NEMA 3R rainproof enclosure protects against weather, vandalism and nuisance tripping. Factory wired, assembled and tested. All-in-1 construction for factory assured terminations. Suitable for use as service entrance equipment when installed in accordance with the National Electric Code. Accepts copper or aluminum wire for added installation flexibility. Rolled edge door for cord protection. Dead front construction prevents accidental contact with live parts. Stay open position on door for convenience. Padlock provision. UL/CUL Listed (power outlets). 19.125" height x 9" width x 3.5" depth, 47 lb. Convertible Indoor Plug-on Neutral load center for plug-on neutral breakers. Built with a shielded copper bus bar. UL listed.
Eaton MBE2040B200BTF Combination Ring Meter Breaker/Center Reliance 30216A Manual Transfer Switch Square D QO130M200PRB QO Main Breaker Load Center
All-In-One, BR branch breaker type, EUSERC, 25 KAIC, 20/40 distribution, BW2200 main breaker included. Bottom and top feed, ring style, UG/OH service. 5-3/8" depth x 14-7/16" width x 43-3/8" height. Built for generators up to 7500 watts. Features 6 large toggle switches that provide control of circuits, backup pushbutton breakers for each circuit and a wattage meter to monitor the appliance load on the generator. Features a built-in NEMA L14-30, 30 watt power cord inlet, 3/4" pre-wired conduit that attaches to load center. NEMA Indoor cabinet. 30 amp maximum combined load at 125 vac, 30 amp maximum combined load at 250 vac. 6 single-pole circuits: 4 single pole 15 amp circuit breakers, 2 single pole 20 amp circuit breakers. One double-pole circuit. 10 gauge cord recommended. 7.5" height x 7" width x 4.5" depth, 9 pounds shipping weight. Full color packaging. UL1008 Listed. Built with a shielded copper bus bar. UL Listed.
POWER PEDESTAL/METER RV 100A  Coghlan'S 31406CRK Manual Transfer Switch Kit Reliance Generator Transfer Switch
Ring-type metered earth burial pedestal with 50 amp and 30 amp GFCI circuit protected receptacles. 16-gauge zinc coated G-90 steel, with electro-deposition finish, resists corrosion and fading. NEMA 3R rainproof enclosure protects against weather, vandalism and nuisance tripping. Factory wired, assembled and tested. All-in-1 construction for factory assured terminations. Suitable for use as service entrance equipment when installed in accordance with the National Electric Code. All terminals accept copper or aluminum wire for added installation flexibility. Rolled edge door for cord protection. Dead front construction prevents accidental contact with live parts. Stay open position on door for convenience. Padlock provision. UL/CUL Listed (power outlets). 19.125" height x 9" width x 3.5" depth, 59 lb. All inclusive, fits generators up to 7500 watts with 20 or 30 amp L1420 or L1430 power outlets. Includes 6-circuit transfer switch with watt meter, 30 amp outdoor power inlet box, 10 Ft. 10 gauge 30 amp power cord, spare 20 amp power cord plug end for smaller generators, easy-to-follow installation and operating instructions, and wire connectors. Full-color packaging. Maximum of 6 single-pole circuits or 1 double-pole circuit. 60 amp maximum combined load at 125 volt, 30 amp at 250 volt. Four 15 amp single pole circuit breakers, two 20 amp single pole circuit breakers. UL1008 Listed. Suitable for hardwire connection to PB50 power inlet box. Switch has 10 toggle switches to control the circuit breakers under generator power. It is set up at the factory to be connected to a double pole 30 amp breaker (to control a central air conditioner or electric water heater), a double pole 20 amp breaker (to control a well pump) and six 15 amp 120 volt circuit breakers. Integrated, interchangeable one-inch circuit breakers in the switch make multiple connection options possible. 12,500 maximum generator wattage. Analog watt meter. 13" height x 11.75" width x 4.5" depth. UL 100B Listed.
   
 
1